Voltage drop is one of the power quality problems affecting power users. This happens due to the higher demand for electric power. Or a short circuit in the transmission system. This causes a voltage drop is one of the power quality problems affecting power users. This happens due to the higher demand for electric power. Or a short circuit in the transmission system. This results in drop in Solving of voltage drop problems in power distribution model with distributed generator were presented with MATLAB program by installing a generator in the distribution system. Therefore simulated a case study 5 case 1 simulation by not installing a generator at any bus case 2 simulation by installing a Generator at bus 1 case 3 Simulation by installing a Generator at bus 18 case 4 simulation by Generator installed at bus 33 and case 5 simulation by Generator installed at bus 13 17 21 31 to study the suitable location of generator installation to solve the problem of voltage drop.

As the worlds energy resources are currently insufficient to meet human needs energy-saving and energy-efficient appliances have to be invented that are readily available and accessible to everyone. To have enough energy to meet human needs and to reduce the waste from the waste of energy resources each year to meet the demand for energy that can be produced by itself. This research presents the construction of a portable DC to AC voltage converter or “Constrution of Portable DC to AC Voltage Converter” which can be operated through a solar cell. By charging energy from the sun and storing energy at the battery. and can also bring electrical energy to use inside the pressure converter There is an inverter circuit that converts voltage from DC to AC so that AC power can be used in daily life. which has a lighting system power socket USB port and helps reduce electricity bills in the house and is convenient to carry From the experimental results of creating a portable DC to AC voltage converter it can be used in daily life and saves electricity and is also clean energy from sunlight that does not cause pollution like a generator that uses oil. be a generator

In this article the construction of a high-frequency high-voltage commercial flyback transformer to supply an input voltage for a tesla transformer is proposed. The purpose of a demonstration is a breakdown through the air gap of electrode. To confirm the proposed method the design of control of a flyback converter by using a commercial flyback transformer is rated with a 10 to 15 kV output voltage to supply a tesla transformer at a rated 30 kV and 120 kHz. The experimental results of an output breakdown design of the electrode and the setting for a 1 cm space are constructed. The electrodes consisted of the following: sphere–sphere electrode plane–plane electrode sphere–plane electrode and rod–plane electrode. It was found that there was a breakdown at the output electrode in all cases. Accordingly there was a breakdown with a 2 cm sphere diameter with reference to the IEC 60052-2002 standard; after that it was compared with the standard table and the atmospheric and temperature at the laboratory were adjusted resulting to a high voltage equal to 31.5 kV.

This research study analyzes the problem of waste water from the burning of palm trees which are used as fuel for power generation of palm ash. It is used to ferment biogas as a fuel for power generation where a large amount of wastewater from the gas digester is completed. The wastewater is then pumped out of the gas digester. Biological in large quantities Therefore to study the analysis of wastewater to find a method for designing a wastewater treatment system from high voltage systems from the corona discharge principle when adding ozone it is necessary to analyze the chemical effects of the wastewater according to the standard values of the Department of Industrial Works.

The objective of this research is to study the combustion characteristic of a low-pressure vertical port burner using computational fluid dynamics (CFD). The simulation model was created using Fluent 6.3 in 3D-model of the same size of the burner. The CFD results were verified by measuring the temperature around the burner head and a vessel. Moreover the results of conventional vertical port burner having the swirl angle of 90o and the inclination angle of 90o (CB-S90I90) and two swirl port burners (SB) being SB-S90I13 and SB-S30I90 were compared. The temperatures obtained from CFD and experiments were similar which the error was less than 9%. From the CFD’s results the temperature and heat flux of the SB-S90I13 burner were higher than those of the CB-S90I90 burner. The maximum temperature and heat flux of SB-S90I13 burner were 1445 K and 5291 W/m2 respectively. It was implied that the combustion characteristic and heat transfer to the vessel of SB-S90I13 burner was better than that of CB-S90I90 burner. It was resulted that the thermal efficiency of SB-S90I13 burner was better than that of CB-S90I90 burner which was the percentage energy saving of 6.93%.