This research is to study in heat transfer of hot water tank from an air conditioner which is a cylinder type and has a hot water pipe around the tank. It is used for finding a position and a pattern of distribution of the hot water pipe around the tank in the highest heat transfer condition. The study uses the cylinder of hot water tank filled 45 liters of 25 oC water. An experiment separates in 3 positions of pipe wrapping which are the bottom the center and the top of the tank. Then 80 oC of hot water run thought the hot water pipe which is wrapped around the tank for 120 minutes. The result of the experiment shows that tubing position that causes the highest heat transfer is at the bottom of tank. Pipe wrapping at the bottom of the tank has the heat transfer higher than the top of the tank at 30%. Furthermore this experiment studies in spacing of hot water pipe. There are 3 types for testing which are spacing hot water pipe as one time two times and three times of diameter of pipe. The result illustrates that spacing the hot water pipe can significantly increase the heat transfer. The heat transfer of spacing the hot water pipe in three times of diameter of pipe is higher 5.8 % than spacing in one times. In addition this research is to study in the effect of turbulent flow on the heat transfer by installing agitator in order to stir water in the tank. The result is that water stirring in the tank for increasing the heat transfer is not effective for investment because the energy using for stirring is higher than the enhanced heat transfer

The objectives of this study is to increase efficiency of steam boiler 2.5 ton per hour which used liquid petroleum gas LPG as fuel. bringing heat recovery inside boiler chimney stack to preheat feed water with technology heat Exchanger Economize. Taking the economizer with its pipe length of 1000 mm and 62 mm diameter for 64 pipe is a cross flow with staggered tube to increase water temperature before entering the boiler pass to deaerator The study is carried out to compare the differences and savings of the feed water temperature steam boiler efficiency and fuel consumption between having the economizer installed and uninstalled. reference to study The result after installed the heat exchanger economizer the feed water is passed into steam boiler deaerator higher temperature from 38.30°C to 67.20°C which leads to increase efficiency of steam boiler from 81.59 % to 85.65 % meaning that the fuel consumption of steam boiler will be reduced 4.97 %

This research’s objectives were to develop an energy saving rotary dryer for paddy using hot air recovery system and to evaluate the energy using. Rotary dryer divided rotating cylinder made of 304 stainless steel 2 mm of thickness 39 cm and 200 cm of diameter and length. The inverter was used to control speed of gear motor of 0.5 HP and rotating speeds of 1-3 rpm. The inside of cylinder composed screw and capture flights. The cyclone system was used to dust separating from the system. The moisture trap contained silica gel the outlet hot air was reduced moisture and recovered using. The fiber glass insulator was applied for reducing energy loss. The heating box composed 3 set of 1600 W heaters and blower motor power was 0.5 HP. In the experiment the drying temperature was varied of 50 60 70 and 80oC and cylinder speed was varied of 1 2 and 3rpm (15.66 10.66 and 5.66min of drying time). The initial moisture content of 10 kg paddy was 29.7?0.6 %wb. The result show that the optimum conditions drying temperature and cylinder speed were 70-80oC and 1 rpm (15.66 min) and final moisture content was 9.2-11.8 %wb. From the save energy testing found that the reducing of SEC was 0.4-0.6 MJ/kg water per drying cycle. There for this developed dryer can save energy using

The objective of this work was to study the feasibility of recovery N-Methyl-Pyrrolidone (NMP) and acetone solution in cleaning the slider fabrication process in the manufacturing process of hard disk drive by distillation. The operating parameters such as pressure (50 - 500 mbar) temperature (60 - 110 C) and time (20 - 70 minutes) were investigated. The highest purity of solution was ca 98.12 %of N-Methyl-Pyrrolidone at 110 C 200 mbar with 30 minutes that it is sufficiently purity to be re-used. This solution could be produced with 0.33 Liter/hour with 405 Baht/Liter (excluding investment cost) that would be saved 565 Baht/Liter and environmentally friendly with clean technology.

WC powder was obtained from recycling cemented carbide scraps. This metal power contained tungsten carbide (WC) at 89.17% titanium (Ti) at 4.90% tantalum (Ta) at 3.56% niobium (Nb) at 1.31% and molybdenum (Mo) at 0.93%. Its particle size and distribution was in the range of 0.03-85.31 µm. After quality improvement of the metal powder by ball milling screening and separating the compounds the result showed that the particle size of the metal powder was decreased to 0.01-0.10 µm (10-100 nm). The average size of the powdered particle was 28 nm. The tungsten powder was in more perfect condition by 95.85%