In this article the construction of a high-frequency high-voltage commercial flyback transformer to supply an input voltage for a tesla transformer is proposed. The purpose of a demonstration is a breakdown through the air gap of electrode. To confirm the proposed method the design of control of a flyback converter by using a commercial flyback transformer is rated with a 10 to 15 kV output voltage to supply a tesla transformer at a rated 30 kV and 120 kHz. The experimental results of an output breakdown design of the electrode and the setting for a 1 cm space are constructed. The electrodes consisted of the following: sphere–sphere electrode plane–plane electrode sphere–plane electrode and rod–plane electrode. It was found that there was a breakdown at the output electrode in all cases. Accordingly there was a breakdown with a 2 cm sphere diameter with reference to the IEC 60052-2002 standard; after that it was compared with the standard table and the atmospheric and temperature at the laboratory were adjusted resulting to a high voltage equal to 31.5 kV.

This research study analyzes the problem of waste water from the burning of palm trees which are used as fuel for power generation of palm ash. It is used to ferment biogas as a fuel for power generation where a large amount of wastewater from the gas digester is completed. The wastewater is then pumped out of the gas digester. Biological in large quantities Therefore to study the analysis of wastewater to find a method for designing a wastewater treatment system from high voltage systems from the corona discharge principle when adding ozone it is necessary to analyze the chemical effects of the wastewater according to the standard values of the Department of Industrial Works.

This research is presented by the designing and constructing test package that are divided into three types; the liquid insulator solid insulator and gas insulator. These materials are provided by in country in order to construct the test package for the results of expected to have at least error. This leads to reliability and validity in this study. The design of the liquid insulator of test package was conducted by the standard IEC 156 in which the material tested used oil transformer. Additionally its solid insulation was the range of catching objects and adjusting using the sheet of bakelite. Furthermore its gas insulation used acrylic was consisted of gas inside oxygen of pressure at 2 Bar. Three types of test could be supplied AC high voltage to test package causing of breakdown via insulators. After that taking note the value of breakdown was the liquid insulator of test material at 29.86kV its solid insulator at 36.32kV and its gas insulator (oxygen) at 48.40 kV

Frozen fish thawing method using an Electrostatic Technology from a High Voltage Electricity (ETHVE) is one of an alternative method. Due to this method the material has a uniform temperature and also increase the temperature of the material resulting in a short time thawing process. Therefore the objective of this research is to develop the thawing method for frozen tunas using an ETHVE compared to some water immersion method. The experiment was carried out by using frozen tunas with an initial temperature of -18 °C then thawing frozen tunas with the ETHVE until the temperature of the tunas increased to 5 °C. Then the tunas were steamed until the temperature of 60 °C compared to that water immersion method. The qualities of steamed tunas were determined by percentage of tunas meat and tunas blood. The results showed that the tunas thawing techniques using the ETHVE provided a uniform temperature of tunas meat both the surface and the center the piece of tunas. In addition this technique also provided a higher percentage of tunas meat and tunas blood and some surface area has slight burns compared to that water immersion method. The frozen tuna which was thawed by using the ETHVE method which some surface and center using temperature at 5 °C and –2 °C respectively. The tunas surface area were slightly burned the percentage of tunas meat and tonas blood were 45% and 5% respectively. During the frozen tuna thawing using the water immersion method has the surface and center temperature at 12 °C and –2 °C respectively; The tunas surface area were very burnt the percentage of tunas meat and tunas blood were 42% and 3% respectively.

This article presents how the analysis an insulation of high voltage transformer bushing. The purpose is to analysis the moisture in the bushing to evaluate the approach for maintenance. The analysis rely on the principle of the Polarization and Depolarization Current (PDC) technique which is a technique for analyzing the insulation of high voltage equipment to test high voltage transformer bushing for a case study. This method is performed by energize 1000 Vdc into a bushing in period of time and then switch off the circuit for discharge current. Finally we calculate the moisture of main insulation of high volt bushing as well compare with standard moisture of criteria. The method is useful of preventive maintenance plane of high volt bushing and reduce the failure in the power system.