The objectives of this research were to study the stress intensity in run-flat metal wheels and to design a new type of run-flat wheels that can be used in a small armored regular truck. Experimental methods and finite element methodologies were applied in the research process. The results obtained by comparing the strain values from the two methods demonstrated the consistency of both methods. The differences in stress values were in 10 -16 percentages which could confirm the capability to analyze the stress distribution and deformation of run-flat by a finite element method. Proven processes and procedures in Pre-processing with SolidWorks Simulation were utilized to design run-flat wheels and a reverse engineering process was next used to create wheel rims and design the cross-sectional shape of new run-flat wheels made of composite materials which have an important reactant; a polymer group and aluminum oxide powder added to enhance the strength. The designed parameters consisted of 1) the width of the run-flat wheels 2) the internal and external radius in which the internal radius depending on the size of the wheel rim and the outer radius which is a variable that determines the height of the run-flat wheels 3) the design of a lockset for tightening the run flat wheels to the wheel rims 4) materials used in the structure of the run-flat wheels and 5) tire pressure. The run-flat wheels designed and built into three-piece parts were designed for ease of wheel assembly or disassembly out of the wheel rims. By analyzing the intensity of stress accumulated in a conventional run-flat wheel (run-flat metal wheel) the stress generated in a run-flat wheel did not exceed the limit of the Yield stress and had a safety value between 3-5 times for new run flat wheels with a maximum stress of 26 MPa. Sizing and cross-sectional dimensions of run flat wheels thus resulted in stress which was in the range that could be withstood and acceptably employed. It was also possible to reduce the height of the flat wheels to make the rear flats lower and increase the width of the run flat wheels which would help distribute more weight to the wheel rims.

The objective of this research was to design run flat wheels made of aluminum for passenger cars and investigate the stress strain and deformation of run flat wheels and their components. The original 17 inch run flat wheels were made of AISI 1020 steel with a weight of 11.3 kg per wheel. The main problems were from the high-level weight as well as the untighten connection together with noticed gaps taking place between the run flat wheel and the wheel. Therefore in this study the AISI 1020 material was changed to the Aluminum 6063 T6 material. The Numerical methodology using the finite element program was also chosen to indicate the comparative differences in the strain values engaged at various locations of both run flat wheels and pan wheels. The results obtained from both approaches using SolidWorks Simulation Program uncovered the consistent results of the experiments with a 10-16% difference in strain values. The complicated 17 inch wheel pan model was next built using reverse engineering and employed as a key reference to design the cross-sectional area of the new run flat wheels made of Aluminum 6063 T6. All these two parts could be connected tightly. The SolidWorks Simulation program was employed to design and examine the strength of both designed aluminum run flat wheels made of aluminum and the wheel pan made of 17 inch aluminum alloy to build passenger cars. The finite element model was furthermore applied for the run flat wheels made of aluminum 6063 T6 and it provided run flat wheels composed of 2 light weighted pieces. The stress strain and deformation measured were proven and suggested in the test. The output Von Mises stress did not exceed the Yield stress within the linear elastic limit and 3 times safety integrity value. The results from the study were that the obtained run flat wheels allowed the driver to continuously drive for a further 50 kilometers at a speed of 50 kilometers per hour without losing control. They allowed possible tire repairing or replacing when situated in a safe and convenient location.

This thesis offers the design of the impulse generator 1.2 / 50 μs which applies for studying and generating the lightning impulse to test the endurance of the electricity transmission line. Moreover this study analyses the factors which affects the impulse waveform by using Orcad program. The parts of prototype device can find in the general market. After the efficiency test of the electricity transmission line the result shown that the device should have the high capability to endure the temporarily high impulse. This minimizes the dangerous from the electricity system.

The objective of research was to study and analysis the Electric vehicle structure of Rajamangala University of Technology Phra Nakhon. The Electric vehicle designed to save energy protect environment and cognitive development of student by used the computer software help in the design Material selection Finite Element Analysis Appropriability of the Electric Vehicle Structure and di s p l a c e m e n t of the vehicle structure by using the computer program help in the calculation for the Finite Element Method including to the development of engineering skill. The research must to create the Electric vehicle prototype to suitable and the structure have lightweight and strong for the electric vehicle and focuses on energy efficiency and the material of structure used steel pipe. This research can use to other working structure and future vehicle in sustainable. The vehicle has two seats Capable of running speed to 0-80 km/h the weight at the vehicle structure not over 1 0 0 kg. And the material of structure used steel pipe. This researching can use to other working structure and future vehicle in the sustainable.

Freight is major source of income of the State Railway of Thailand (SRT); which had revenues of one billion baht a year. The development of freight by rail system to be fart punctual and safe is important. Knuckle pin serves tension and shear stress in pulling Rolling Stock. Strength testing of Knuckle pin must be done by technical and engineering knowledge. SRT has 6000 Rolling Stocks; that means 6000 Knuckle Pin has been used and it is likely to increase due to the construction of the Double Track Project and the purchase of new Rolling Stocks. The efficient Knuckle Pin prolongs lifespan and SRT would have benefit on saving cost of maintenance and increase safety in the transportation of goods. This research is aimed at creating the understanding about the quality of the Knuckle Pin modeled Nat Mall. The pin would be test by Standard Test Methods for Tension Testing of Metallic Materialsand the Standard Test Method for Analysis of Carbon and Low-Alloy Steel by Spark Atomic Emission Spectrometry and Hardness Testing Machine and Microstructureto determine the cause of pin’s damage. This study will contribute the standardization of the quality of the Knuckle Pin which is used in Rolling Stocks of SRT.