Deterioration of reinforced concrete deep beam structure caused by chloride is severe andtakes up wide area even though the structure is not exposed to sea water or brackish water. Even the structure which is far from sea water or brackish water is affected by this problem.When the reinforced concreate deep beam structure is affected by chloride steel reinforced inside the structure is corroded resulting in reducing the cross-sectional area of the reinforced steel affecting load capacity deflection and beam failure. If there is no repair or strengthening such capabilities are continuously reduced until it is no longer safe to use the beam. Therefore it is necessary to repair or strengthening the deteriorated structure to be safely used. This research investigated strengthening of deteriorated reinforced concrete deep beam caused by chloride with 4 formats of carbon Fiber sheets to seek guidelines for the most efficient strengthening. The resultshowed that the strengthening by the 4 format of carbon fiber sheet could increase ultimate loadcapability yet could not improve ductility of the deteriorated beam to become close to the beamthat is not deteriorated. The strengthening that could increase the maximum ultimate load capability was the table format strengthening. In addition the strengthening that the carbon fiber making 45 degrees with the length of the beam could best prevent diagonal cracks.

The objectives of this research were to construct a jar oven for the production of roasted chicken using heat from far-infrared radiation and to find the amount of electricity and specific energy consumption used in the production of roasted chicken. The physical properties in terms of color softness cooking yield and water holding capacity of roasted chicken were also investigated. By using far-infrared radiation at electrical power levels of 1000 1200 and 1400 watts to roast marinated chicken which had an initial mass of about 1650 grams until the mass of the roasted chicken had a lower than 1220 grams. From the experimental results it was found that the production of roasted chicken at far- infrared radiation with a high electrical power level requires significantly less electricity and specific energy consumption than that with low electrical power level (P≤0.05). Roasted chicken breasts with far-infrared radiation at 1400 watts had significantly higher lightness (L value) but lower redness (a value) and yellowness (b value) than those of 1000 watts (P≤0.05). However lightness (L value) yellowness (b value) and redness (a value) of the roasted chicken breast with far-infrared radiation at 1200 watts were not significantly different from those at 1000 and 1400 watts (P>0.05). The shear force and water holding capacity of roasted chicken were significantly increased when the electrical power levels of far-infrared radiation increased (P≤0.05). Moreover the electrical power levels of far-infrared radiation (1000 1200 and 1400 watts) did not significantly affect the cooking yield of roasted chicken (P>0.05).Sponso

Dyes contaminated in wastewater that negatively affecting the environment and human health. The objectives of this study to prepare activated carbon from Salacca zalacca (Sumalee) seeds activated by 36 mmol/g KOH dye solution and activated carbon ratio 20:32 ml/g for dye removal. The influents of dye removal from wastewater by Salacca zalacca (Sumalee) seeds activated carbon were investigated as initial dye concentration activated carbon and dye solution ratio and contraction time. The moisture content the iodine number the methylene blue index and the functional groups by FTIR technique of the Salacca zalacca (Sumalee) activated carbon were characterized and the kinetics adsorption were also analyzed. The results showed that the activated carbon was the microporous material the highest dye removal from wastewater was 7.50 ± 0.25 mg/g the equilibrium time was 150 min with the activated carbon to dye solution ratio of 1:500 g/ml for 200 mg/l initial concentration. The kinetics of the adsorption process can be described by a pseudo-second order model (R2 = 0.9999). When increasing the initial concentration of dyes the adsorption efficiency was increased. The amount of activated carbon increased resulting in lower adsorption efficiency and the equilibrium time was longer

. This research aimed to study the acidification processes of carving vegetable using acid conditioning machine under emperature and pressure control which was developed in this study. Four acidification procedures were done at normal atmospheric pressure (method 1) under vacuum pressure for 10 (method 2) and 20 min (method 3) and vacuum pressure alternating with normal atmospheric pressure for each of 1 hour. There were two main parts of acid conditioning machine including the temperature controller inside the pickle tank and heat conductor tank and the pressure controller inside the pickle tank. The pickling temperature was stabled at 40oC under the pressure of 0.5 Bar. PLC (Programmable Logic Controller) program was used to write the ladder for controlling all processes and display through SCADA system. The results showed that the acidification method by soaking the carved-rose carrot under vacuum pressure alternating with normal atmospheric pressure showed the shortest time to equilibrium by 7 hours. Then the carved-rose carrot was packed in the glass jar followed by sterilized in boiling water for 15 minutes and stored at room temperature for 7 days. Total bacteria count Escherichia coli and Yeast-mold were not exceeded than the standard limit. Staphylococcus aureus was not detected throughout the storage periods

The objective of this research is to study the combustion behavior of a gas-saving burner S-10 using computational fluid dynamics (CFD). The simulation model was created using Fluent 6.3 in 3D-model of the same size of the burner. LPG pressure of 4 psi was released for this study. The combustion behavior was shown in temperature contour and velocity vector. The CFD results were verified by measuring the temperature around the burner head with a vessel. From the study it was found that the CFD’s results of flow velocity and combustion temperature distributions were validated with the experimental values. The CFD’s result errors were less than 10.35% and 11.87% comparing with the velocity and temperature measurement respectively. The fluid flow and combustion behaviors can be described by this CFD model. Moreover the CFD model of the gas-saving burner S-10 can be applied to improve the thermal efficiency of the burner in the future.