This research studies the production of bacterial cellulose from Acetobacter xylinum TISTR 975 with pineapple peel juice a low cost carbon source and coconut water as nutrient and carbon source. The factors influencing the production were studied including incubation time type of carbon sources and ratio of mixed carbon sources. In addition the characteristics of the produced bacterial cellulose were investigated using Fourier Transform Infrared Spectrophotometer (FTIR) Scanning Electron Microscope (SEM) Thermogravimetric Analyzer (TGA) Differential Scanning Colorimeter (DSC) and x-ray Diffractometer (xRD). It was found that the coconut water produced the amount of bacterial cellulose higher than the pineapple peel juice with 10 days of production. An addition of the coconut water into the pineapple peel juice increased the amount of bacterial cellulose. The characteristics of two bacterial celluloses from two different sources were nearly similar but the one from the pineapple peel juice had higher impurities. It can be concluded that the pineapple shell extract could be used as low cost carbon source for bacterial cellulose production.

Durian has been very popular not only local people but also tourists. As a result there are many durian peels wasted so this research is explored the utilization of durian peels. Durian rind is a biological waste but contains high amount of crude fiber. This research aims to study using durian rind powder to replace wheat flour in butter cakes at 5 10 and 15 % (w/w) (DRB-5 DRB-10 and DRB-15). Physical properties chemical composition and sensory evaluation of the butter cakes were analyzed. The results showed that durian rind powder contained 51.43 % of crude fiber. Increasing of durian rind powder in butter cakes showed significant decreasing of lightness (L*) blue–yellow component (b*) springiness and cohesiveness values while green–red component (a*) hardness and gumminess values were significantly higher than the control sample (BC) (p≤0.05). Dietary fiber content of the products shown significantly increased by 13.98% for DRB-5 48.92 % for DRB-10 and 54.84% for DRB-15 as compared with BC (p≤0.05). The acceptance scores of DRB-5 including appearance odor taste texture and overall liking scores were highest. There are 300.28 kcal for 1 serving of butter cake which contain 1.70 gram of dietary fiber. However durian rind powder can be used as a food ingredient and source of dietary fiber in other food recipes for further studies.

This research aimed to develop compound of prototypes polymer bio-composites from cassava starch (CS) reinforced with agriculture residue the rind of durian fruit. Cellulose extracted from durian rind using hot sodium hydroxide and bleaching treatment with hydrogen peroxide. The removal of lignin and hemicellulose components from durian rind were investigated by fourier transform infrared spectroscopy (FT-IR). Cassava starch bio-composite films were prepared by solution-casting technique which includes 0-50 wt% of durian rind (DR) or durian rind cellulose (DRC) as reinforcement agent and urea/glycerol (GU ratio = 50:50) as plasticizer. The physical and chemical properties of thermoplastic starch (TPS)/DR and TPS/DRC bio-composite films were investigated. The percent elongation at break of bio-composite films were increased when compared to control CS film. From 15TPS/DR (80/20) films showed increase the elongation at break from 7.28 to 14.00% when compared to CS control films. While 15TPS/DRC (80/20) bio-composite films exhibited that the highest elongation at break to 77%. Durian fiber (DR or DRC) loading decreased the water absorption of plasticized bio-composite films. Furthermore incorporation of DRC in composite can be enhanced film stability in water better than DR. Therefore the effect of DRC reinforcement agent on TPS bio-composite films can improve water resistance and mechanical properties especially in terms of flexibility. Finally the waste of bio-composite films was degraded completely in soil burial test.

This research aims to study the parameters have affected the pipe which was studied the heat transfer characteristics of a heat pipe with a mesh wick. The heat pipe made from copper tubes with intemal (ID) as 10 and 12 mm and length of 30 cm which was installed a copper mesh wick inside a tube. Three working fluids are distilled water ethanol and refrigerants-11 (R-11). The filling ratios is 50% with respect to evaporator volume. The operating temperature at the evaporator section is: 50 70 and 90 oC. The condenser section has cooked by water with a flow rate of 0.5 L/min. Then all of the experimental data were compared with the heat pipe without copper mesh wick. It was found that heat pipe at ID 12 mm yielded a better heat transfer rate when compared with heat pipe without a mesh wick. The heat pipe produced a heat transfer rate value of 7.3 W and heat pipe efficiency of 58.5 at evaporator section’s temperature of 90oC. In addition the mesh wicks will help transfer the working fluid in the condenser section return to the evaporator section. The condensed liquid had spread around the walls of the heat pipe. The working fluid was condensed to the evaporator section then affected to a higher heat transfer rate.

The objective of this study 1) To study the shape of the template from the process of making basketry 2) To design a template hyacinth wicker products creative products 3) To test the woven pattern of water hyacinth wicker 4) To create a unique product that is more valuable to the local wisdom and value. Consumerism toward the development of water hyacinth wicker patterns. By specifying a sample group of 57 people. The tools used in the research consisted of the satisfaction questionnaire on the template pattern water hyacinth weave basketry to local creative concept product. The results of the design of the water hyacinth wicker pattern design to the product of local identity concept found that the design shape can be a shape that has a concept as a creative product. Form 1 wicker-shaped pattern template from water hyacinth leaves The product is a chair with an average of 4.58 Form 2 template oval shaped wicker basket shape. The product was a basket of legs with an average of 4.48 Form 3 basket shaped shape from the bowl shape the product received the basket has a value of 4.22. All 3 forms that can be developed in the form of products that can satisfy level most satisfactory shape is the molds for Basketry 1. The product is a chair that is beautiful the proportion of products is suitable for use and strong products are local and creative in the process of water hyacinth wicker requires a template for forming. The original material used to make the wicker template is plywood or foam material. During the study phase the researcher invented the material for making water hyacinth woven basket template using rubber water mixed with plastic watercolor foamed foam templates are used for easy handling and longer durability.