The purpose of this research is to facilitate technology of limiting excess electricity from the source before supplying to the electrical appliances. The distribution of electricity by Metropolitan Electricity Authority (MEA) frequently exceeds the needs of households and factories due to the fact that the voltage has to be enough to send electricity to users who are located further at the end of the voltage grid lines. Most electrical appliances are designed to perform at optimum voltage of 220 Volt. The voltage optimization system controls the incoming voltage to fit the optimum voltage of electrical appliances which will reduce the overheating phenomenon and thus lengthen the lives of electrical appliances. It can save 8-14% of total energy being consumed and potentially reduce CO2 emission. This analysis system can be used for industries in the range of small to large companies. From the development of remote monitoring using a control via internet or 3G/4LTE the voltage optimization system showed practical power saving results of the reduced power usage and lengthen the lives of electrical appliances; that leads to reduction of emerging electricity resource eradication of natural resources increase the chance of marketing competition and energy sustainable

This research aimed to study the design and development to assist in bringing the car seat into the production process and the risk assessment approach to ergonomics to suit operator. Emphasizing the importance of work and trying to create design tools. Organize work appropriately in accordance with the competency and performance of each individual. Using the principles of biomechanics analysis applied in the analysis along with an assessment of the risks by taking into consideration upon 3 factors. 1. The level of severity. 2. The level of frequency.3. Safety measures at the different parts of the body due to which the body must be borne from the outside and in the work. By bringing knowledge of mechanics the proportion of the body anatomy and physiology is able to create the relationship in a model way of Ergonomics which occurs according to the gesture. The use of tools lifting heavy parts and labor pull push and press researchers found in the process of lifting car seat weighs 14.5 kg dimensions width 45 cm length 55 cm and 100 cm in height is the distance of the car seat to shelve. Assembly point distance of 200 cm research has fixed this issue by adjusting the distance of the car seat and shelves by only 50 cm distance can be reduced down to 150 cm and adjust the position of the lifting cushion to reduce twisting torso while assess the biomechanics model of the behavior of all employee in improvement on quality both before and after work station.

The research objective is to utilize the waste water at 12ºC to 20ºC in exchange with the process water at the temperature of 29ºC. After entering the heat exchanger the process water will have the reduced temperature of 19ºC and then will be delivered to the cooler so the temperature of the process water will further be reduced to 15ºC to involve in the production process. Consequently the cooler’s energy use is lower. Since the common coolers used in these days have problems about the clogged system caused by shrimp residue the cleanup of the system is difficult and the maintenance cost is high. With this problem the research and development of the new heat exchanger is carried out resulting to the Shell and Tube Heat Exchanger type with the angled lid and the waste water flow control pads allowing the water alternatingly running through the lower part and upper part of each pad. The process water will flow in the 6 sets of the stainless tubes with 2 mm. thickness ½ inch diameter and 6 meter length. The space between the set is 5 centimeters for exchanging heat with the waste water flowing outside the tubes. The study conclusion is that the new heat exchanger can reduce the temperature of the process water to 19ºC so it can save the electricity cost of the cooler for 886485 baht per year and make the cleanup easier without taking off the equipment parts thus lowering the maintenance cost as well.

Design and development of solar cells in electric vehicle prototype intended to Design and development of solar cells in electric vehicle prototype Case study electric cars of Rajamangala University of Technology Phra Nakhon. The research process begins with the solar experiment model Solar Thin Film a bent size 19.2 x 9.5 cm technology has applications in Unmanned Aerial Vehicle install to a source of clean electricity generation using 80 Solar Thin Film Cells controlled by Arduino mega size 101.52x 53.3 mm Programming software by Arduino-1.6.9-Windows and Show the result at LCD Solar Monitor Charger from batteries store the electrical energy size 12V/28AH 6 pack for the results showed that such a circuit can charge electricity 5A to 1 hour and to expand the use of rechargeable battery electric prototype instead of using electric vehicle prototype from charging normally Requires 480 Solar Thin Film Cells in trial period hypothesis 6 hour/day. In term of investment evaluation simple payback period is expected to be 4 years. Considering sensitivity analysis it is found that the most sensitive factor is electricity cost cost Solar Thin Film and the cost of Evlink Fast Charge Solution respectively. The results of this study can be used to support decision making in design and development of electric vehicle prototype in the next generation more efficiently

Bags product design from Na Muen Si woven Na Yong District Trang Province which is special project that objective is to study pattern of Na Muen Si woven to bags product design from Na Muen Si woven Na Yong Trang province and study about customer satisfaction this work devide by into 5 step about customer satisfaction and analyze information of student groups Faculty of architecture and design Rajamangala University of technology Phra Nakhon between 20-25 years old from 120 consumer Data were analyzed using percentages and averages. The result of study most consumers are female 62.50% bachelor’s degree 3rd years 29.17% with income 10001-15000 bath per month 52.50% The result satisfied for bags product from Na Muen Si woven Na Yong District Trang Province. It found that most consumers satisfaction was high an average total of 4.21 and when considering the appropriateness of the bag with patterned of Na Muen Si woven found that most consumers are satisfied with the briefcase Bueng Bua pattern. Next is the duffel bag Phi kun pattern.