Braking system is the main of safety for motor vehicle. It uses to slow down or stop of vehicle movement. Normally braking system can not to adjustable in the recently. The brake efficiency depends up on to 3 factors by the perfection of brake equipment friction coefficient of road surface and the brake proportional. The factor of the perfection of brake equipment and friction coefficient of road surface can not be control. But in case of the brake proportional can be set up to suitable. In the other hand if the brake ratio is unsuitable the driver may be risk to danger from the loss of vehicle control. From this reason the aim of project is to study of the brake proportional affected to vehicle control. By the test condition consist of 2 cases: braking performance testing and vehicle stability testing. In case of braking performance testing is consider to deceleration braking distance and time of braking. For the vehicle stability testing is determined with yaw angle pitch angle sideslip angle and wheel lock up condition. However the bolt of testing is the road test and using the FMCSA standard for the testing guideline. The result of the braking performance testing shown the maximum deceleration was appeared on brake proportional 80:20. But the braking distance and time of braking are least because of the non-continuously of deceleration from the driver. Therefore the braking distance and time of braking depend on the continuously of deceleration. In term of vehicle stability testing discovered to the each of brake proportional are risk to danger for the driver especially on the 100:0 because of the value of sideslip angle is more than the critical point and the rear axle is lock up.

The objective of research was to study and analysis the Electric vehicle structure of Rajamangala University of Technology Phra Nakhon. The Electric vehicle designed to save energy protect environment and cognitive development of student by used the computer software help in the design Material selection Finite Element Analysis Appropriability of the Electric Vehicle Structure and di s p l a c e m e n t of the vehicle structure by using the computer program help in the calculation for the Finite Element Method including to the development of engineering skill. The research must to create the Electric vehicle prototype to suitable and the structure have lightweight and strong for the electric vehicle and focuses on energy efficiency and the material of structure used steel pipe. This research can use to other working structure and future vehicle in sustainable. The vehicle has two seats Capable of running speed to 0-80 km/h the weight at the vehicle structure not over 1 0 0 kg. And the material of structure used steel pipe. This researching can use to other working structure and future vehicle in the sustainable.

Design and development of solar cells in electric vehicle prototype intended to Design and development of solar cells in electric vehicle prototype Case study electric cars of Rajamangala University of Technology Phra Nakhon. The research process begins with the solar experiment model Solar Thin Film a bent size 19.2 x 9.5 cm technology has applications in Unmanned Aerial Vehicle install to a source of clean electricity generation using 80 Solar Thin Film Cells controlled by Arduino mega size 101.52x 53.3 mm Programming software by Arduino-1.6.9-Windows and Show the result at LCD Solar Monitor Charger from batteries store the electrical energy size 12V/28AH 6 pack for the results showed that such a circuit can charge electricity 5A to 1 hour and to expand the use of rechargeable battery electric prototype instead of using electric vehicle prototype from charging normally Requires 480 Solar Thin Film Cells in trial period hypothesis 6 hour/day. In term of investment evaluation simple payback period is expected to be 4 years. Considering sensitivity analysis it is found that the most sensitive factor is electricity cost cost Solar Thin Film and the cost of Evlink Fast Charge Solution respectively. The results of this study can be used to support decision making in design and development of electric vehicle prototype in the next generation more efficiently

The aim of this research is to create the center of mass testing machine for vehicles with maximum mass 3000 kilograms. By the performance of this machine is able to determine the center of mass 3 axis by horizontal longitudinal and vertical. On the other hand the verities of mass from 50 to 250 kilograms and the several of weight distribution at horizontal and longitudinal are applied to the condition of testing for reasonable to the position of the center of gravity for vehicle. The result of research discovered to the performance of center of mass tester was activated following to test conditions. Furthermore the position of the horizontal of center of gravity depends on the weight distribution at horizontal axis and an increasing of mass under non-uniform along the longitudinal and horizontal axis. In term of the position of the longitudinal of center of gravity the weight distribution at longitudinal axis and an increasing of mass rate are points. Otherwise the weight distribution at longitudinal axis and an increasing of mass are effect to the position of the vertical of center of gravity.

The aim of this research is to study the varieties of weight density distribution affect to the center of mass and vehicle stability. The weight density distribution tester was designed and changed the position of mass. Base on the center of mass is main points of vehicle stability. On the other hand FMCSA standard was applied to field test for considering of the brake performance and vehicle stability. The results of research discovered to the mass distribution on horizontal plane and fixed position Y1 are absolutely influence under an increasing 50 kilograms of mass condition. For the mass distribution on longitudinal plane and fixed position Z2 and Z3 are affected to the increasing of mass 100 and 150 kilograms respectively. Otherwise under an increasing of mass 200 and 250 kilograms there is non-influence to the weight density distribution. In term of the braking performance it’s depends on the lateral mass distribution especially the center position of mass installed on longitudinal and horizontal plane and close up on the front axle (Y2). For the vehicle stability results the position (Y2) is the highest influence for yaw rate and sideslip. Otherwise the position (Y3) or the position of mass installed on longitudinal plane and nearly at the left wheel on the rear axle. Additionally wheel lock-up condition was appeared on the front axle only. Because the behavior of the weight distribution on front axle was decreased lead to mass distribution on longitudinal plane.