This research aims to study the appropriate drying condition and extraction solvent for extracting protein and antioxidants from the porcine placenta. Three levels of drying temperature were used in this study which were 50 60 and 70ºC the result shows that the best drying condition for porcine placenta was 70ºC for 4 hours because this condition provided the least drying time and the lowest moisture content of porcine placenta (3.80±3.36% dry basis). After that the fresh and dried porcine placenta were extracted by using three solvents which were deionized water (DI) phosphate buffered saline (PBS) and hexane. The efficiency of extraction was investigated by measuring the crude protein and antioxidant of the porcine placenta. It was found that there was no protein and antioxidant in fresh and dried porcine placenta extracted by hexane. However the protein was found as 0.05±0.01 and 0.04±0.01 mg of bovine serum albumin/100 mg fresh for fresh porcine placenta and 0.12±0.030 and 0.07±0.016 mg of bovine serum albumin/100 mg fresh for dried porcine placenta extracted by DI and PBS respectively. In additional the antioxidant was found as 1.13±0.03 and 1.29±0.04 mg of trolox/100 mg fresh for fresh porcine placenta and 3.37±0.02 and 3.59±0.01 mg of trolox/100 mg fresh for dried porcine placenta extracted using DI and PBS respectively.

The performance investigations of subcritical ORC supercritical ORC and trilateral Rankine cycle (TLC) power plants with the heat source temperatures of 210-250°C were conducted and compared in this study. Several working fluids were evaluated. A MATLAB code was developed and used in this study. The thermodynamic properties of the working fluids were calculated by using NIST REFPROP program. The justification of the code was validated with a result taken from the literature. The optimal operating conditions were searched using the golden-section technique. The maximum net output power of 141.72 kW was obtained when using the supercritical ORC plant with R141b as its working fluid and the heat source temperature was at 250°C. The corresponding cycle efficiency was 16.25%. When using the subcritical plant at the same heat source temperature the maximum net output power of 133.40 kW and cycle efficiency of 15.70% are obtained when pentane is used as the working fluid. Furthermore the net output power of 133.82 kW and cycle efficiency of 14.90% are obtained when using R141b as the working fluid in the TLC power plant. According to the off-design simulations an appropriate adjustment of the working fluid flow rate can mitigate the variation of the net output power.

This research objective was to apply thermoelectric module model TEC12710 as a preheater and dehumidifier for red chilies dryer. The heat side and cool side of Thermoelectric module affected by supplied electricity were used to produces the low humidity and warm air in preheater before charging to the main electric heater of dryer. Fresh red chilies were selected as a sample in the prototype testing during the use of preheater assisted main heater and using only main heater. The test results are compared with the sample dried under the natural sun drying. The experimental results show that the preheater can condense the moisture in air with the highest MER of 0.083 kgwaterh-1 at cold side of thermoelectric module and can heat the air up in 10°C of temperature with hot side of thermoelectric module. The final moisture content of sample is only 10%wb with the slightly changed in color when compared with the sample from sun drying. The using of preheater with main heater gives a higher specific moisture extraction rate lower specific energy consumption 14 MJ energy used and can dry faster than 10 h when compared with the using of only main heater.

The research was to develop environmental packaging from composite materials hyacinth fiber rice husk and coconut fiber for temperature preservation to replace the use of foam packaging that cannot be degraded naturally. In the composite materials water hyacinth fiber rice husk and coconut fiber at the ratios 7: 1: 2 1 : 1 : 2 and 1: 1: 1 were extruded by heat using isocyanate glue as a solder and testing the physical and biological properties of composite materials as fiberboard. For testing of temperature preservation of the bio packaging heat transfer test to obtain the bio-packaging for the environment the composite materials of fiber water hyacinth rice husk and coconut fiber at the ratio of 7 : 1 : 2 was the most appropriate type. Since it had a density of 0.7 grams per cubic centimeter strength of 26.76 MPa moisture content of 3.8 percent ages and swelling of 26.63 percent ages. In dry condition at room temperature it could store heat for 2 hours and could retain the cold temperature as shown for the temperatures rising from 4 to 30.7 degree Celsius within 2 hours. This research therefore presents a new alternative method of natural fiber composite materials application for temperature preservation in order to reduce the use of foam containers and increase cost value to natural bio waste materials.

Brake system is used the friction between disk and pads. In the driving conditions the brake behavior from the driver is difference. Based on this reason the damage on disk and pads are occurring. Nowadays the ratio of compound materials in pads is several and involved automotive industry has not available enough to experiment. Thus it is difficult to brake pads damaged analyzing in several driving conditions. In this problem the mechanical property tester is main tool for experimenting. And test procedure based on the Brake lining and disc brake pads compressibility JIS D 4413 [7]. The experiment emphasizes on the flexibility behavior and internal energy by volume with 3 types of brake lining and pads. For the experiment focused on conditions by normal apply brake repeat apply brake and suddenly apply brake. The results revealed the normal apply brake condition the maximum and minimum of flexibility behavior was appeared on brake lining and pads type A and type C with testing temperature at 2000C. By the repeat and suddenly apply brake conditions the brake lining and pads type C and type A with 300C is given to the maximum and minimum flexibility behavior. In case of internal energy by volume the maximum and minimum energy was appeared on pads type C and B at the 300C of testing temperature. For the testing temperature at 200 and 4000C the pads type A and type B were got the maximum and minimum energy respectively. On the other hand at the high flexibility behavior is given to high internal energy at the high temperature of the apply brake condition.