Currently the automotive industry plays an important role on the economic growth in Thailand. As the same time the waste of automotive parts has increased as well. As a results the automotive parts made from three different natural fiber parts was studied consisting of hyacinths sugarcane and pineapple leaf fiber. By of 50 x 250 x 20 mm of mold dimension the specimens were produced under 700 W of heating stick and measured temperature by a K type of thermometer. There were 3 same proportion specimens made from: 1) sugar cane fiber: husk: latex adhesive 2) water hyacinth fiber: husk: latex adhesive 3) pineapple fiber: husk: latex adhesive in the ratio of 25:25:50 by weight which were formed under temperature between 100GC and 105°C at 5 MPa of pressure and leading to find out the bending moment ability. The test results show that the specimen made from sugar cane fiber has the highest value 5482.5 Nand 4061.11 N/mm2 of bending moment and bending stress respectively. It was more than specimen made of water hyacinth 29.84 % and pineapple fiber 65.01 %.

Molds manufacturing to produce chloroprene rubber product with carbon steel over time the mold surface will wear. From the original. The practice in the industry often uses surface coatings (Hard chrome method) or change materials to create molds. Therefore this research is to study the effect of corrosion or wear. To see the size of surface mold changed in the experiment. Based on a tolerance of 0.1 millimeters at the molding point and after molding in the actual work conditions of a 2-3 weeks sample and mold size measurement. At less than 10 times the permissible coordinate value is 0.01 millimeters. The experiment found that. The wear of carbon steel molds was formed with chloroprene rubber. It has a very small value when referenced to the tolerance coordinates which is not significantly reduced when the rubber specimen size is determined. The allowance range is 10 μm to 100 μm. Therefore the design of chloroprene rubber to make molds with carbon steel. It can help reduce production costs. Without replacing with corrosion-resistant materials or adding coatings.

The objectives of this research are to propose an efficient and proper model that fits the cassava and rubber yields data. A generalized estimating equation (GEE) and a linear mixed model (LMM) with spatial correlation following the conditional autoregressive model (CAR) were adopted. The dependent variables are the cassava and rubber yields collected each month in every province of Thailand. The factors considered are rainfall averaged temperatures and regions. The results from GEE and LMM show that the factors influencing on the cassava and rubber yields are rainfall averaged temperature and region. Both GEE and LMM fit the correlated data. The GEE is used to explain the influence of factors on the yields in all provinces while the LMM is used to explain the influence of factors on the yields in each province.

The research is study motives the affect participation in quality assurance personal of Faculty of Engineering Rajamangala University of Technology Phra Nakhon from example group of 182 people which classified by sex ages position educational degree field of work and working life. This research is used themethod is collecting data by question tool themethod is questionare tool fo collected data that could be two categorized include knowledge skills and attitudes. The questionnaire is five rating scales that analyze the result by frequency percent average the average of standard deviation and T-test independent by using one way ANOVA. The results were as follows : From one hundred percent of the personnel of Faculty of Engineering Rajamangala University of Technology Phra Nakhon whom 63.70 persent classified by the educational field and 36.30% support line are ready to enter into Asean community which could be seen average in whole picture. After considering in three aspects the result appeared that knowledge and skills of personnel are also average. However the attitude of personnel was considered in a high level. Hypothetic test result was found that there was no difference among the personnel with difference sex ages educational degree field of work and working life in their readiness in entering Asean Community. position

This continued 2nd year researchaims to study the development of the para rubber press machine with wrought pattern for continued 2nd-year. Used natural para rubber mixed in a Ta-kuong by normally practical para rubber farmer style to evaluate the rubber press machine. A machine consists of the 11 roller sets in vertical pathway with press sticks on top. The components are as follows: a water press roller with a slope surface to reduce the diameter around 1-1.5 mm from a center the 3-pair sets of normal press rollers and the 2 duo sets of wrought pattern rubber press rollers with the induction motor at 1430 rpm. The rotating transmission based on belts and chains with a . The evaluated results produced the dried para rubber sheets thickness at 3.79 mm on average as the 2nd rubber sheet type standardin marketing need. From a top tray a farmer can put a sticky para rubber piece to a roller press machine easier than normal just 5.9 second on average with lower hand power to handler of the rubber pieces. In finally the wrought patternrubber sheets by a worker to carry the ta-kuong to a top tray of a rubber press machine and a rubber press man to put the para rubber pieces to a machine thus the completed 186 wrought rubber sheets per hour on average.