Recently the consumption rate of vehicle is continuously an increase as an economic growth. This not only causes the massive traffic but also effects on the accidental capacity especially the road accident between car and pedestrian. The most of victims who dead are Vulnerable Road Users are crashed by the front-end structure. Regarding this problem; the possibility of the Pedestrian Crash Simulator has studied and established following the Euro New Car Assessment Programs in Pedestrian Protection. This simulator can be adjusted in 3 axles of tested position. Besides the body forms are used as impactors which are pushed the high speed drive unit via the iron less linear motor. In addition the simulator can be adjusted from 0 to 65 of degree comparing the horizontal line. As a result the limitation of the Pedestrian Crashed Simulator is linear speeds because of budget limitation. The highest of performance is not more than 3000 mm/s with 19.46 mm/s2 of speeds and acceleration respectively. However this simulator can be developed the ability by addition of the power unit and control equipment. The highest acceleration should be 35.06 m/s2 within 1.76 m. of magnetic track rail to equivalent the specified condition of the EURO NCAP (in Pedestrian protection). Pedestrian protection testing machine

This study Motorcycle Tourism Potential of Kanchanaburi Province aims to study the motorbike tourism potential of Kanchanaburi. And suggestions for motorbike tourism development in Kanchanaburi Province. The research employed a quantitative research. The research sample was 400 tourists who travel by motorbike in Kanchanaburi tourist attractions. The research tools was a questionnaire with open-ended questions. The data is described by frequency percentage and standard deviation. Most participants were male 30-39 years old had obtained a bachelor degree managed private businesses and earned income of naked motorcycle. The results of the research indicate that opinions about motorcycle tourism potential in Kanchanaburi Province ranked from the highest to the lowest potential is travel cost Presentation and information view and the biker challenge of the route Security facilities of motorcycle tourism policy tourist attractions people motorcycle group and motorcycle club and marketing. Suggestions on motorcycle Tourism development in Kanchanaburi. There are 8 points: price control public relations adding motorcycle rest area ensure safe travels adding motorcycle tourism services establish regulations related to Motorcycle tourism conservation of tourist attractions and Promote activities in Motorcycle group.

Brake system is used the friction between disk and pads. In the driving conditions the brake behavior from the driver is difference. Based on this reason the damage on disk and pads are occurring. Nowadays the ratio of compound materials in pads is several and involved automotive industry has not available enough to experiment. Thus it is difficult to brake pads damaged analyzing in several driving conditions. In this problem the mechanical property tester is main tool for experimenting. And test procedure based on the Brake lining and disc brake pads compressibility JIS D 4413 [7]. The experiment emphasizes on the flexibility behavior and internal energy by volume with 3 types of brake lining and pads. For the experiment focused on conditions by normal apply brake repeat apply brake and suddenly apply brake. The results revealed the normal apply brake condition the maximum and minimum of flexibility behavior was appeared on brake lining and pads type A and type C with testing temperature at 2000C. By the repeat and suddenly apply brake conditions the brake lining and pads type C and type A with 300C is given to the maximum and minimum flexibility behavior. In case of internal energy by volume the maximum and minimum energy was appeared on pads type C and B at the 300C of testing temperature. For the testing temperature at 200 and 4000C the pads type A and type B were got the maximum and minimum energy respectively. On the other hand at the high flexibility behavior is given to high internal energy at the high temperature of the apply brake condition.

Admittedly a disc brake plays an important role in the auto part industry since it concerns directly with safety. Therefore the wide range of disc brake has been designed in order to develop its heat ventilation. There are two physical kinds of brakes: front-vented disc brake and backvented disc brake. As a result such difference affects directly to the heat ventilation which is a vital factor of the brake’s capability. The project team recognizes its importance and tries to create the test to find out the temperature diffusion of the disc brake with the hope to evaluate the coefficient of the heat convection varied by the temperature changing in both kinds of brakes under the forced heat convection in the steady condition. However the steady heat conduction and radiation value will not be counted because it is insignificant. The JASO C406: 2000 Standard is adopted as a guideline in the test. The outcome coefficient of heat conduction will be used in the simulation via the Finite Element Method (FEM) in order to study the temperature diffusion and heat ventilation of both kinds of brakes at each temperature level. Consequently the experimental work reveals then the heat convection coefficients of both kinds are unidirectional. The heat convection coefficient of the front-vented disc brake is 4.40 % in average higher than that of the back-vented disc brake. From the simulation the front-vented disc brake can ventilate the heat better than the back-vented disc brake at 3.02 % in average. It can be summarized that the front-vented disc brake has more temperature difference than the backvented disc brake. Hence the front-vented disc brake likely gets more stress from the temperature than the back-vented disc brake and might be damaged during the operation more than the another type.

Nowadays the automotive industry in Thailand has been widely growing. Brake pad is one of the automotive products that play a vital role in automotive industry because it is the most critical seeurity part. Consequently testing products for quality are extremely requested. However the precise equipment and function tests which show the real effects are not available enough and cost a lot. Therefore they cannot response to the deman in the automotive industry development. In this study the frictional test jigs for friction measurement JIS K7125 [5] and the clutch facings for automobiles JIS D4311 [6]. A study of the frictional test emphasizes on the static friction (μs) and kinetic friction (μk) in different condition. There are 3 specimens of brake pad supposted by the industry company. These specimens were tested and the results from the pin-ondisk and those from the friction testing were compared. The results revealed the correspondence of the two-sided results but the pin-on-disk’s friction coefficient is more than the friction testing’s friction coefficient by 19.56%. Moreover the coefficient of friction varies according to the temperature Besides the static friction (μs) is likely more than kinetic friction (μk) and tends to differ considerably under high pressure condition.