Nowadays the Thailand automotive industry widely grows. Brakepad is one of the automotive productions that role to automotive industry because it is the most critical security parts. Consequently testing products for quality are extremely requested. However the equipment and function tests are not enough and are also high cost so it cannot supports to the automotive industry development. In this work the initiation and design of frictional test were carried out. The testing procedure is referred to The special test jigs for friction measurements JIS K7125[5] and Clutch facings for automobiles JIS D4311[6].A study of the frictional test emphasize on the static friction(l-ls) and kinetic friction(l-lk) in different condition. There are 3 specimens of brake pad supported by the industry company. These specimens were test and compared between the pin on disks result and the friction testings result. The two-sided results from the analysis correspond but the pin on disks friction coefficient is more than the friction testings friction coefficient by 19.56%. Moreover the coefficient of friction tends to follow the temperature. Besides the static friction(l-ls) is likely more than kinetic friction(l-lk) and will be high difference in high pressure condition.

The purposes of this research were to build and develop a standardized test used to measure English abilities compliant with the curriculum of the fourth-year students of rajamangala University of Tecnology phra nakhon. There were group of the students namelt the frist group which consisted of 57 students takung the electronic tests via the use of the electronic test and to and obtain a computer program prototype for measuring English abilities.

The research aimed to study parameters affecting the stress intensity and stress distribution as well as the deformation of run-flat tires for passenger cars using the Finite element method. Both experimental methods and finite element methodologies were employed in the research process. The results were obtained by comparing the strain values from the two methods to demonstrate the consistency of both methods. The differences in their strain values were shown in the range of 10-16% confirming the analyzing capability in this problem through the Finite element method. At the pre-processing step both procedures and methods were proven with SolidWorks simulation program together with experimentation. These consequences were incorporated to assist the design of run-flat tires. Parameters affecting the stress intensity and stress distribution were evaluated to understand the effects on deformation of the new designed run-flat tires. The reverse engineering process was thus applied in the research process by scanning with FARO P06-05 and creating solid modeling 3D models with Geomagic program for SolidWorks. These could assist in designing the reverse- engineered tire pan. Three components were additionally designed to support the ease in assembling or removing run flat tires from the pan. Run flat tires were finally designed for passenger cars typically the most common small cars. The weight of this car was limited at not more than 1800 kg and the thickness of the wheel pan was 17 inches. The analysis information assumed that the vehicles weight was distributed equally throughout all 4 wheels. The material used to make the run flat tires was a composite tire type that could withstand the pressure occurring from the weight of a passenger car. The results of the analysis demonstrated that the maximum stress on the run flat especially at the position where the run flat surface was in contact with the road was 30-45 MPa which depends on the location of contact with the road. Thus it affected the stress distribution on the wheel pan. The parameters obtained from the study affecting the stress distribution and deformation were accounted to be such types of materials made for run flat tires cross-sectional area and width of run flat tires.

The objectives of this research were to study the stress intensity in run-flat metal wheels and to design a new type of run-flat wheels that can be used in a small armored regular truck. Experimental methods and finite element methodologies were applied in the research process. The results obtained by comparing the strain values from the two methods demonstrated the consistency of both methods. The differences in stress values were in 10 -16 percentages which could confirm the capability to analyze the stress distribution and deformation of run-flat by a finite element method. Proven processes and procedures in Pre-processing with SolidWorks Simulation were utilized to design run-flat wheels and a reverse engineering process was next used to create wheel rims and design the cross-sectional shape of new run-flat wheels made of composite materials which have an important reactant; a polymer group and aluminum oxide powder added to enhance the strength. The designed parameters consisted of 1) the width of the run-flat wheels 2) the internal and external radius in which the internal radius depending on the size of the wheel rim and the outer radius which is a variable that determines the height of the run-flat wheels 3) the design of a lockset for tightening the run flat wheels to the wheel rims 4) materials used in the structure of the run-flat wheels and 5) tire pressure. The run-flat wheels designed and built into three-piece parts were designed for ease of wheel assembly or disassembly out of the wheel rims. By analyzing the intensity of stress accumulated in a conventional run-flat wheel (run-flat metal wheel) the stress generated in a run-flat wheel did not exceed the limit of the Yield stress and had a safety value between 3-5 times for new run flat wheels with a maximum stress of 26 MPa. Sizing and cross-sectional dimensions of run flat wheels thus resulted in stress which was in the range that could be withstood and acceptably employed. It was also possible to reduce the height of the flat wheels to make the rear flats lower and increase the width of the run flat wheels which would help distribute more weight to the wheel rims.

This research analyzes the parameters affecting the penetrating resistance of shells on the armor surface by the finite element method. In this study the results were compared with real bulletproof armor firing tests and finite element simulations. modeling of bulletproof armor using Solid Works program. Creating and simulating armor firing pattern using ANSYS Explicit Dynamic program. damage test is based on National Institute of Justice level 3 standards with material of the ammunition is 7.62 mm tungsten carbide (WC) and speed 847 + 9.1m/s. there are two types of bulletproof armor used in this simulation 1. SKD11 2. Aluminum AL7075. The simulations is into 1 category Simulation of stacked armor plates. The sizes of the armor plates are 6 8 and 10 mm and the angles of firing of bulletproof armor are 0 30 and 45 degrees. result of this simulation armor thickness and firing angle are factors of penetration resistance. when the angle of the projectile is tilted it will cause the projectile to deflect reducing the frictional contact from the impact.