This research aimed to experimentally study of solar panel efficiency with water cooling. Three mono-crystalline solar panels with the capacity of 80 W (for each panel) were used for this test. The first panel was a solar panel without water cooling. The second panel was a panel with water spray cooling. The last panel was a solar panel with water drop cooling. The cooling water flow rate was varied to 50 75 and 100 LPH. From the test it was found that the temperatures of all solar panels had the similar trends. The solar panel efficiency decreased when the temperature of solar panel increases. The solar panel efficiency increased when the cooling water flow rate was increased for both of water spray cooling and water drop cooling. For all water cooling flow rates the water spray cooling solar panel performed higher efficiency than water drop cooling solar panel. The highest solar panel efficiency in this test occurred when the water spray cooling flow rate of 100 LPH.

The objective of this research is to construct a phased array device to be able to inspect all sizes of welded pipes and to study materials suitable for creating a phased array. The results obtained from testing both materials are PLA plastics carbon fiber. In order to obtain the force exerted on the material and the intensity of the force exerted on the same material it is found that the strength of the comparison between the two materials is different from the PLA plastic test. Of carbon fibers will be strong and lighter than plastic. Result from the test for Elastic In the impact and strength tests of both materials it can be used to examine pipes with a circumference of 50 centimeters to 100 centimeters and to use a 34 mm. length phased array probe with a width of 24.6 mm. 36 degrees angle and then adjust the strap as needed to reduce the steps during the use of inspection equipment.

Brake system is used the friction between disk and pads. In the driving conditions the brake behavior from the driver is difference. Based on this reason the damage on disk and pads are occurring. Nowadays the ratio of compound materials in pads is several and involved automotive industry has not available enough to experiment. Thus it is difficult to brake pads damaged analyzing in several driving conditions. In this problem the mechanical property tester is main tool for experimenting. And test procedure based on the Brake lining and disc brake pads compressibility JIS D 4413 [7]. The experiment emphasizes on the flexibility behavior and internal energy by volume with 3 types of brake lining and pads. For the experiment focused on conditions by normal apply brake repeat apply brake and suddenly apply brake. The results revealed the normal apply brake condition the maximum and minimum of flexibility behavior was appeared on brake lining and pads type A and type C with testing temperature at 2000C. By the repeat and suddenly apply brake conditions the brake lining and pads type C and type A with 300C is given to the maximum and minimum flexibility behavior. In case of internal energy by volume the maximum and minimum energy was appeared on pads type C and B at the 300C of testing temperature. For the testing temperature at 200 and 4000C the pads type A and type B were got the maximum and minimum energy respectively. On the other hand at the high flexibility behavior is given to high internal energy at the high temperature of the apply brake condition.

Nowadays an automotive industry steadily has been growing and playing a major role on economy development for many years. The crash box is one of the most important parts for safety but it was found that the crash boxes manufactured domestically are not met international standard requirements. This is due to process and material limitation. This process for automotive safety test requires high budget and there is unclear approach for specific test. Therefore a study of crash boxes referred to energy absorption project was conducted as the alternative materials for product. Consequently this project was aimed to design and test crash boxes which made from the diversity of the alternative materials such as aluminum aluminum reinforced by foam resin reinforced by fiberglass resin reinforced by water hyacinth and resin reinforced by water hyacinth and husk. In addition it was also emphasized in studying energy absorption behavior and physical deformation of crash boxes after dynamic and static energy being applied. The experimental works were applied for these tests in partly referenced to US NCAP and ECE R29 standard for automobile collision test. Testing all types of crash boxes indicated that the aluminum reinforced by foam type was able to absorb energy at 189 MJ/m3. It is higher than resin reinforced by water hyacinth and husk at 1 MJ/m3 as 188 times. Furthermore the comparison of the energy absorption (per unit volume) between the aluminum reinforced by foam type and the steel type from the previous project equivalent 20 MJ/m3 found that it is 8.45 times of difference. While the front impact test was not successful because the size of crash boxes was not suitable for the energy volume. It was a cause for non-available calculation of energy absorption value.

The aim of this research is to study the varieties of weight density distribution affect to the center of mass and vehicle stability. The weight density distribution tester was designed and changed the position of mass. Base on the center of mass is main points of vehicle stability. On the other hand FMCSA standard was applied to field test for considering of the brake performance and vehicle stability. The results of research discovered to the mass distribution on horizontal plane and fixed position Y1 are absolutely influence under an increasing 50 kilograms of mass condition. For the mass distribution on longitudinal plane and fixed position Z2 and Z3 are affected to the increasing of mass 100 and 150 kilograms respectively. Otherwise under an increasing of mass 200 and 250 kilograms there is non-influence to the weight density distribution. In term of the braking performance it’s depends on the lateral mass distribution especially the center position of mass installed on longitudinal and horizontal plane and close up on the front axle (Y2). For the vehicle stability results the position (Y2) is the highest influence for yaw rate and sideslip. Otherwise the position (Y3) or the position of mass installed on longitudinal plane and nearly at the left wheel on the rear axle. Additionally wheel lock-up condition was appeared on the front axle only. Because the behavior of the weight distribution on front axle was decreased lead to mass distribution on longitudinal plane.