The purposes of the study were to examine the quality of life of the motorcycle taxi drivers in Bangkok Metropolitan region and to investigate the development of the quality of life of the motorcycle taxi drivers in Bangkok Metropolitan region. The sample of the study drawn by the method of stratified simple random sampling consisted of 507 motorcycle taxi drivers in Bangkok Metropolitan region. The questionnaire was used as the data gathering tool. The statistics applied for data analysis consisted of Frequency Percentage Mean Standard Deviation Crosstabs T-test F-test at 0.05 level of significance. The results of the study demonstrated that the majority of the motorcycle taxi drivers were male between 36-50 years old completed secondary education were married lived in rentedhouses earned average daily income of 200-400 Baht earned average monthly income of 5000-10000 Baht spent average monthly expenses of 5001-10000 Baht earned their living as the motorcycle taxi drivers for 3-5 years had white vehicle registration plates and drove motorcycle taxis in Bangkok area. The study of opinion concerning the quality of life revealed that the motorcycle taxi drivers in Bangkok Metropolitan region expressed their opinion on overall aspects of quality of life at a high level Mean =3.72. When each aspect of the quality of life was examined it was found that safety aspect was at a highest level next below were the aspects of work life spirit and soul participation family life health and communication. According to the aspects of income and environment the study showed a moderate level of opinion respectively however the aspects of housing and education were found at a high level. With regard to the opinion on the development of quality of life the motorcycle taxi drivers had a moderate level of opinion Mean=3.21.

The objectives of this research were to study the reduction of organic compounds by the biological action substance of the effluents from palm oil mil to produce singe cell protein. The wastewater taken from the third pond of the wastewater treatment system which was already used for biogas production was found to have pH 6.5. The organic matter like COD (3679 mg/L) Oil& grease (133 mg/L) as well as the total solids and the minerals were much lower than those of the decanter effluent. The reduction of organic compounds by using the biological action by Candida tropicalis TISTR 5146 5045 and C. lipolytica TISTR 5151 were studied. The results indicated that C. tropicalis TISTR 5146 which was cultivated in palm oil mill at initial pH 5.5 and diluted with water to the ratios of 1:5 at agitation on the shaker of 150 rpm at room temperature gave the highest yield of biomass of 2.52 g/L and COD reduction of 94.38 % after 3 days of cultivation. The optimal condition for C. tropicalis TISTR 5146 cultivation was that the ratio of palm oil mill effluent to diluted water was 1:5 containing 10 g/l glucose and 10 g/l yeast extract at initial medium pH 5.5 in the shaking flask of 150 rpm at room temperature. The highest biomass obtained was 12.53 g/L while the cell consisted of protein and fat for 43.12 % and 0.34 % respectively.

This research is to study and develop a DC motor speed control by using Visual Basic.Net 2008 in computer programming to use the computer and the microcontroller is processing from computer via the serial port. So that a signal to the motor driver circuit motor speed work as assigned. By the speed can be entered via the computer screen is measured in rpm. and motor control to control the PWM (Pulse Width Modulation) control circuit and the principles of the hardware by using the digital output signal of the microcontroller control Motor speed can be configured to be from 100 to 3000 rpm. And the motor starts to spin at maximum speed and then gradually reduce the speed down to the specified value. Control both the speed and the average error of 4.6% compared to the speed measurement using infrared light. And found that at speeds below 100 rpm. to a maximum error of 12% and the error decreases when the speed increases. The error value is at least 2000 rpm. and 3000 rpm the speed error is 0.5%

The purpose of this study was to study the history of a cultural architecture resources and environment in the local community. The history that found was used to be information to find the development of potentiality of cultural tourism to carry on the cultural activity which related to the local community to encourage local people to beneficially manage the resources and to accommodate the tourism in Nan local government. All of these operations were focused on the cooperation of monks and local people by debating. This study collected data by using random survey questionnaire of local people tourists and tour guides. Moreover the interview of local instructors local people and other people was also used in this study. The development of the potentiality of cultural tourism at Wat Satharot still need help from government by adding a streetcar park at Wat Satharot and promoting a tourist attractions in variety of advertisement. The local people combine in to community to manage the tourism. For tour guides and tourists they need some souvenir shop and antique and beautiful sightseeing.

This research is the study for effected of orientation setup workpiece from Rapid Prototyping process. The objective of this study has to minimize average tolerances of specimen size and roundness of cylindrical specimen. Specimens were studied with orientation direction define 3 axis (X Y Z) and created by rapid prototyping Machine with FDM Technology. The Measuring average tolerance of specimen size and roundness of cylindrical specimen used the Coordinate Measuring Machine (CMM). The Result showed that test specimens were formed along the X axis having lowest of average tolerances. The increasing average tolerances of diameter depend on the increasing diameter size. The roundness value of cylindrical surface forming the X axis was the most circular cylinder. The roundness value of cylindrical was depend on the increasing of diameter size. It shows that when the workpiece has a larger diameter. The workpiece would be circular cylinder is decrease