This objective of this research is to study the development of the pararubber tapping knife in order to determine the optimum of the edge and oblique angle and to compare the efficiency of the electrical motor and Je-Bong knife. The product was manufactured by iron steel carbon S45C and AISI 5160 with 75-90 degree edge knife and 0-45 degrees oblique angle. The results can be concluded that the optimum condition of the edge knife oblique knife and the cutting force were 75 degree 45 degree and 3.51-51.42 N respectively. It was found that the cutting force was straightly increased form 0-51.42 N and then gradually decreased. The energy consumption of timber cutting was 0.00370 J/mm3. The quality of the rubber tap using electrical motor was 72.07% which was higher than 2.8 of Je-Bong knife. As the results this product shows the average of rubber timber which is 2.22 mm. in 22.51 s.

The research objective is to utilize the waste water at 12ºC to 20ºC in exchange with the process water at the temperature of 29ºC. After entering the heat exchanger the process water will have the reduced temperature of 19ºC and then will be delivered to the cooler so the temperature of the process water will further be reduced to 15ºC to involve in the production process. Consequently the cooler’s energy use is lower. Since the common coolers used in these days have problems about the clogged system caused by shrimp residue the cleanup of the system is difficult and the maintenance cost is high. With this problem the research and development of the new heat exchanger is carried out resulting to the Shell and Tube Heat Exchanger type with the angled lid and the waste water flow control pads allowing the water alternatingly running through the lower part and upper part of each pad. The process water will flow in the 6 sets of the stainless tubes with 2 mm. thickness ½ inch diameter and 6 meter length. The space between the set is 5 centimeters for exchanging heat with the waste water flowing outside the tubes. The study conclusion is that the new heat exchanger can reduce the temperature of the process water to 19ºC so it can save the electricity cost of the cooler for 886485 baht per year and make the cleanup easier without taking off the equipment parts thus lowering the maintenance cost as well.

This research aims to develop the ceiling board mixed with coconut coir. The 5 ratios of gypsum plaster: coconut coir: sodium silicate: tap water are equal to 1 : 0 : 1: 0.03 1: 100: 1: 0.03 1: 150: 1: 0.03 1: 200: 1: 0.03 1: 250: 1: 0.03 และ 1: 300: 1: 0.03 by weight. The ceiling boards were produced by casting in normal temperature (30 – 35 degree of Celsius). The properties testing of ceiling board mixed with coconut coir followed the TIS 219-2009 standard (gypsum plasterboard) including: breaking load nail pull resistance deflection water absorption density and thermal conductivity coefficient. From the results 1 : 1 5 0 : 1: 0.03 is the most suitable ratio of ceiling board mixed with coconut coir. This developed ceiling boards can reduce the quantity of coconut coir waste and get the good thermal insulation ceiling board products

The project of design and development of textile product using Thai Song Dam’s stitching technique at Supanburi provinces. “Nowadays it was difficult to find someone who loves weaving; however finding someone who loves stitching was more difficult. The designs of stitching pattern were altered by trend; however they still kept in their identity” Mrs. Lamduan Konthong a specialist in Thai Song Dam’s embroidering style said. According to the questionnaire regarding the requirement of the sample it showed that the sample was interested in the textile products for living room decoration such as a backrest pillow a decorating table runner and a lantern. Thai Song Dam’ stitching technique and “Kor Kood” pattern should be applied with the design of the designated products. To find the appropriate fabric for stitching the experiment was done by stitching of “Kor Kood” pattern on the following type of cotton silk linen hemp and knitted fabric. The chosen one was linen fabric because of its light weight good dimensional stability. To create the model of the products and find the appropriate pattern for stitching the pattern was designed by the concept of Art Nuvo characterized by the appearance of woman. From the questionnaire it was found that the satisfaction of the sample regarding the design of the Thai Song Dam’s stitching in textile products were as follows; 66% kept in the identity of Thai Song Dam 72% style the products of Thai Song Dam 58% Thai Song Dam style the design of the products characterized by Art Nuvo 50% suitable the composition of the pattern of the products 74% suitable the whole pattern design of the products 64% suitable the colors of silk stitching on the products 60% suitable the use of colors of the products 60% suitable the size of the products and 62% suitable for the purposes of using.

Education and research is being Develop material that is mixed between rubber and rubber tree’s leaf for product designing. For product design This study is the use of a water timber with a rubber material. For use in product design Type of use and home decoration. In order to achieve the objectives of the research. The research was conducted by researchers at various stages. Data analysis and presentation. In the first part of the research questionnaire has been prepared for the development of product design. The study showed that the structure and the rubber leaves are fragile. It has adopted a water timber to merge. The experimental trial showed that the water timber formwork period is a major cause of water in the rubber sticking to the timber structure. When the latex has chemical and log Waldemar Carlo Night a period of use should not exceed three months at a water timber should be done with low viscosity. The color of the water timber must have a milky white. The collected data before designing it. The researcher has prepared all the tools of the 150 series found that most respondents as guest female age range 25-45 years as the rubber leaves of 94 percent 62.7 opine that the rubber leaves can be. made products of 5-10 species and the collection of data about materials latex with a rubber to make products from those carrying ask 150 people are of the opinion that it should make products partition 32.7 percent secondary. followed by the production of upholstered furniture 20.7 percent and 14.7 percent from the wallet to store data the researcher chose to put the material into a water timber with a rubber curtain room couch and wallet. When the prototype the researchers collected data on products made from latex and rubber leaves a series of 100 questionnaires showed that most of the respondents were female. Between the ages of 25-45 years the average undergraduate. There were government officers And have a monthly income of less than 5000 baht by the majority of respondents thought that. Rubber and rubber leaves the work piece is in good shape. Durable medium Can be used to make the products have 10-50 species with characteristics of both latex and rubber leaves. And all should be improved The research found that people are more interested in a piece of sheet material from a water timber with a timber. For product design Due to a combination of natural materials as a new material with a rubber-patterned rubber leaves a unique structure. It can also be improved by a more specific latex formulation. To be able to make the product even more.