Recently the consumption rate of vehicle is continuously an increase as an economic growth. This not only causes the massive traffic but also effects on the accidental capacity especially the road accident between car and pedestrian. The most of victims who dead are Vulnerable Road Users are crashed by the front-end structure. Regarding this problem; the possibility of the Pedestrian Crash Simulator has studied and established following the Euro New Car Assessment Programs in Pedestrian Protection. This simulator can be adjusted in 3 axles of tested position. Besides the body forms are used as impactors which are pushed the high speed drive unit via the iron less linear motor. In addition the simulator can be adjusted from 0 to 65 of degree comparing the horizontal line. As a result the limitation of the Pedestrian Crashed Simulator is linear speeds because of budget limitation. The highest of performance is not more than 3000 mm/s with 19.46 mm/s2 of speeds and acceleration respectively. However this simulator can be developed the ability by addition of the power unit and control equipment. The highest acceleration should be 35.06 m/s2 within 1.76 m. of magnetic track rail to equivalent the specified condition of the EURO NCAP (in Pedestrian protection). Pedestrian protection testing machine

The purpose of this research is to study the effect of safety measure to construction productivity for ceiling activity by studying a construction of buildings in Bangkok. The safety system composed of (1) stable scaffolding system (2) providing clean and not slip walkways on the scaffold (3) installation of handrails not less than 0.90 meters in height (4) installing stairs (5) providing personal protective equipment for workers (6) are responsible for scaffolding and (7) scaffolding permit document. Cost of the safety system is 23908 baht or approximately 33 baht/m2. Productivity rates for prior and after the used of safety system are 1.57 and 1.41 m2. /person/hr. respectively. The productivity declines for approximately 10.19 % the working time for ceiling could take longer for 10.45 % and labor cost could increase for 10.19 %.

Currently competition in terms of resolution and contrast of photos from digital cameras are widely mentioned. The higher resolution the photos contain; the more details the picture has. This fact enables the more details of pictures which also hold much more capacity of data. This also causes the electronic devices to be updated all the time to cope with those problems. Therefore the conventional devices are obsolete. This research has been developed and applied to improve digital photos with high contrast. The researcher has solved the problems by keeping the average error of the lowest results and improving heat histogram of various curves. The heat will break the histogram of the original image into n part by the concave side of the heat histogram. The part of this histogram is equal to n+1 and then smooth each other heap histogram independently. The result showed that the Tennengrade or contrast of the image is higher than the original one. However it can retain brightness errors (AMBE) as well

The objectives of this research are to propose a linear mixed model (LMM) with spatial correlation for an analysis of rice yields in Thailand to estimate the rice yield in each month of all provinces in Thailand to investigate factors influencing on the rice yields and to construct the maps of rice yields. A linear mixed model (LMM) in which the spatial effects follow the conditional autoregressive model (CAR) is used. The estimated rice yields are used to construct the rice yield maps. The dependent variables are the rice yield in each month of each province. The data are secondary data at a provincial level. The factors considered are rainfall averaged temperatures and regions. The results show that the factors influencing on the rice yields are rainfall averaged temperature and region. The amount of regional effects ordering from largest to smallest values are northestern region southern region western region central region eastern region and northern region respectively. The top ten provinces and months with high yields ranking from largest to smallest values are Ubon Ratchathani in November (1328000 ton) Surin in Novermber (1070000 ton) Si Sa Ket in Novermber (1023000 ton) Buri Ram in November (939400 ton) Nakhon Ratchasima in November (907500 ton) Roi Et in Novermber (852800 ton) Chiang Rai in Novermber (769800 ton) Khon Kaen in Novermber (692800 ton) Maha Sarakham in Novermber (676200 ton) Udon Thani in Novermber (620600 ton) respectively. The rice yeilds maps are easy for readers to identify which areas have high or low yields. They are a useful tool for planning decision making and implementing plans to help rice famers to increase their rice production.

This research study investigated the structure and electrical effect of the La3+ and Sm3+ co-modified BaTiO3 ceramics with formula Ba1-(x-y)(LaxSmyTi)O3. The concentration of of x was fixed at 0.010 while that of y varied from 0.010 to 0.040. The ceramics are prepared by a solid-state mixed-oxide technique. The phase formation behavior is studied using x-ray diffraction (XRD) The dielectric properties with temperature are broad as wide temperature rang. Results showed that co-modified BaTiO3 ceramic ratio of 0.010 to 0.020 still tetragonal structure where the A-site is disturbed by a group of rare-earth doped. In addition we also found that the dielectric constant increases with ratio of 0.010 to 0.020 and respond to higher frequencies that can be used in the applications circuit with high frequency.