This project is intended as a teaching medium air conditioning system and simulation of air conditioning system problems. Some of them have been modified to suit their teaching needs. Arduino microcontrollers are used to control the system. By starting the study of the air conditioning system thoroughly. The microcontroller is written to control the operation of devices like the air conditioning system when the system malfunction. It will be used to analyze the problems of air conditioning. The experimental set will display the voltage and current. The connection points of the air conditioning problem analysis. When the symptoms are bad. The analyst can solve the problem by connecting or pressing the button of the device. The results of the project. The test will measure the difference of the air conditioning unit. And read the amount of current and volume in the system. To diagnose abnormalities and choose a solution to the problem from the kit system that can be displayed to solve the problem that the analyst was correct or not with the LED status light. Based on the performance test a demonstration kit for the demonstration of efficiency of the air conditioning system was provided to 10 experienced air conditioning technicians. 80s of issues. The reliability of the demonstration set and the efficiency of the simulator case study of the electrical system in air conditioning systems is acceptable

Nowadays the measurement technologies are continually growth in advanced. These can be seen in the developed and developing countries that research and develop the products which support the consumer behavior and/or country economy ic growth. However some advanced products are very expensive such as pH meter. Therefore this thesis develops the pH meter which allows the acid-base test of the water and it can be supported the agriculture. The proposed pH meter is included the pH pen sensor temperature sensor water level sensor. The proposed meter can measure the acid-base of the water by sending SMS alert signal via GSM module to the mobile phone of the farmer. As can be seen this thesis can prevent and solve the effect of the high acid-base of the water that possibly flows into the agriculture farm via using SMS alert signal of the mobile phone of the farmer.

Since the details in quasi-homogeneous region will be degraded from a conventional global image enhancement methods such as histogram equalization. This degradation causes from the saturation of the gray levels in equalization process. Then the local histogram equalization for each quasi-homogeneous region will be used in order to improve the details in the regions. To obtain the quasi-homogeneous regions the image can be segmented by using a watershed transform. The watershed transform is based on mathematical morphology; therefore the segmented regions can be effectively separated meaningful. Two adjacent regions in images which almost similar in gray levels can be separted by the watershed transform. In the color image enhancement three spectral bands are enhanced independently. Then all the three bands are assigned to each processed image in order to produce a color composite image. By the proposed algorithm the result images show the better perception on image details. Therefore the high efficiency of image classification can be obtained by using this color image.

The results of the experiments were found that the temperature of the castings was higher than that of the silver alloys. The workpiece temperature is 500C the workpiece is good 26%. The workpiece is 74%. The temperature is 550C. The workpiece is 26%. The workpiece is 74%. The temperature is 600C. The workpiece is 40%. The workpiece is 60%. The workpiece is a fin. There are many factors that cause fins on the workpiece. Use of low-strength mortar In addition the use of excessive compression or heat transfer resulting in the expansion and shrinkage is not equal. This causes the cracking of the metal water to expand at a temperature of 650 ° C. The fine specimen 56% of the workpiece loses 44%. This temperature results in the smallest workpiece caused by the uneven surface. Cause of the cooling rate in each part of the casting is not equal. And at 700 degrees Celsius it is best to cast silver ornaments with pink color because the results show that the work is minimal. There are 70% good work piece 30%

The objective of this research is to develop the high corrosion resistance and good thermal insulation precast adobe wall panels mixed with natural latex. The 6 ratios of Portland cement type1: clay: rice husk ash: straw: rice husk:waterproofed liquid: natural latex: tap water were designed including: 1: 3: 0.3:0.02: 0.02: 0.02: 0: 0.4 1: 3: 0.3: 0.02: 0.02: 0.02: 0.05: 0.4 1: 3: 0.3: 0.02: 0.02: 0.02:0.1: 0.4 1: 3: 0.3: 0.02: 0.02: 0.02: 0.15: 0.4 1: 3: 0.3: 0.02: 0.02: 0.02: 0.2: 0.4 and 1:3: 0.3: 0.02: 0.02: 0.02: 0.25: 0.4 by weight. The precast adobe wall panels castedas same as the common concrete and reinforced by the bamboo. From the resultsthe proper ratio of precast adobe wall panel mixed with natural latex was 1: 3: 0.3:0.02: 0.02: 0.02: 0.1: 0.4 ratio. The properties of the proper precast adobe wall panelincluded density 1810.83 kg/m3 water absorption 17.16 % compressive strength 15.13MPa bending strength 3.01 MPa thermal conductivity coefficient 0.234 watt/m.Kelvin. Moreover the proper precast adobe wall panel mixed with natural latex also was verified by TIS.2226-2548 with properties of impact resistance deflection and hardness in medium duty (MD) level. The proper amount of natural latex effected the precast adobe wall panels to improve the mechanical properties including: increase the compressive and tensile strength decrease the density thermal conductivity coefficient and water absorption.