This research is developed and designed wall clocks decorative home From sawdust waste in the factory Bang Pho district in Bangkok. The study was conducted by testing groups of wood manufacturer Bang Pho community the results are as follows. The study found that the criteria of design analysis from the experts were 3.97 at a high level and the satisfaction of the product production was 4.11 at a high level. When evaluating the overall picture the mean score of 4.04 was high level.

The objectives of this research are to study the production step proper ratio physical properties mechanical properties and thermal insulation of concrete blocks mixed with waste ceramic powder. The ratios of concrete block mixed with waste ceramic powder include Portland cement type1: quarry dust: waste ceramic powder equal to1: 6.8: 0.2 1: 6.7: 0.3 1: 6.6: 0.4 1: 6.5: 0.5 and1: 6.4: 0.6 by weight. Water per cement ratio are 0.6 by weight. The concrete block samples were castedby the general production as same as the ordinary concrete blocks and were tested follow TIS.58. From the results the best amount of waste ceramic powder which put into concrete block is 1: 6.7: 0.3 of ratio. The proper ratios of waste ceramic powder can decrease the density or weight and increase the thermal insulation efficiency of concrete blocks. However the high amounts of waste ceramic powder effect to decrease the mechanical properties concrete blocks that are lower than TIS.58 standard.

This thesis proposes technical performance evaluation and economic decence for the combination of harmonic correction devices in Industry. Currently an electronic device is popularly applied in power network. Although it is a higher performance device than the existing device it still causes the power quality issues and then network failure. Especially harmonic disturbance in the network it is a harmonic source that generates harmonic current into the network. Many types and solutions are available in the present time therefore the suitable and optimal financial solution must be considered. A network model for the analysis of harmonic correction devices suitable solutions and optimal financial has been established in the simulation software that bases on the power and Break Even Point (BEP) equations. The results of analysis shown that the performance of harmonic correction devices suitable solution and BEP of investment in match to the using of a detuned filter bank and an active harmonic filter (case 8) thus these information will be valued for the end-user.

This thesis presents a method of compare the reducing high voltage source more than necessary to the pilot study two plants in case of load near power station the same distance but different. There are 2 methods first method reducing the voltage by adjusting tap transformer. Other method installed by voltage equipment. Regulator in a factory used 2 methods for measured the value of voltage before&after and continued to reduce the voltage until minimum loading that this factory can normal operate. From two trials we found that reducing the voltage by installation voltage regulator/voltage equipment can save more energy cost 10.23% than adjusting tap transformer that can save only 4.66%. And analysis of Specific Energy Consumption (SEC) by reducing the voltage level of the industry. Energy consumption kWh per 1 output (plastic bottles) Then lower from 0.119 kWh per 1 bottle remaining 0.089 kWh per 1 bottle This is in line with the energy analysis that main control electric power.

The objective of this research is to develop a technology management system for industrial Fabric Pretreatment Dyeing and Finishing factory to resolve existing problems caused by manual input. Firstly this research was performed to study the current work-in processes data. After that these data were analyzedranked and grouped for designing and developing a customized oracle database by implementing SQL on a UNIX server. Finally the new system was integrated barcode technology for connection to facilitate works. Before the renovation to input data by an employees it makes to delay time 1440 minutes from actual manufacturing data. The result represent at 260.67 unit/month as well as newly application of barcode technology. According to this system application it has been found that the manufacturing data in production process are real-time monitored. The result of the research can be increase at 94.42 unit/month as well as reduce expenses on documents above 10000 Bath/month. In addition the operator could also be reduce from 4 to 0. Including enhanced with barcode technology can also facilitate communication with customers making business competitive sustainable future.