This research analyzes the parameters affecting the penetrating resistance of shells on the armor surface by the finite element method. In this study the results were compared with real bulletproof armor firing tests and finite element simulations. modeling of bulletproof armor using Solid Works program. Creating and simulating armor firing pattern using ANSYS Explicit Dynamic program. damage test is based on National Institute of Justice level 3 standards with material of the ammunition is 7.62 mm tungsten carbide (WC) and speed 847 + 9.1m/s. there are two types of bulletproof armor used in this simulation 1. SKD11 2. Aluminum AL7075. The simulations is into 1 category Simulation of stacked armor plates. The sizes of the armor plates are 6 8 and 10 mm and the angles of firing of bulletproof armor are 0 30 and 45 degrees. result of this simulation armor thickness and firing angle are factors of penetration resistance. when the angle of the projectile is tilted it will cause the projectile to deflect reducing the frictional contact from the impact.

This research analyzes the parameters affecting the penetrating resistance of shells on the armor surface by the finite element method. In this study the results were compared with real bulletproof armor firing tests and finite element simulations. modeling of bulletproof and bulletproof armor using Solid Works program. Creating and simulating armor firing pattern using ANSYS Explicit Dynamic program. damage test is based on National Institute of Justice (NIJ) level 3 standards with bullets the material of the ammunition is 7.62 mm tungsten carbide (WC). there are two types of bulletproof armor used in this simulation 1) SKD11 2) Aluminum AL7075. The simulations is into 1 category Simulation of stacked armor plates. The sizes of the armor plates are 6 8 and 10 mm and the angles of firing of bulletproof armor are 0 30 and 45 degrees. result of this simulation armor thickness and firing angle are factors of penetration resistance.

This study applied the kunzelstab penetration Test (KPT) or Light Penetrometer to examined penetration resistance values geological profiles and estimate shear strength properties of soils. KPT tests were carried out on steep slopes that exhibit potential slope movement in Chiang Rai province. The principal uses of the KPT are examined; i.e. correction method for N’KPT’ soil profile and allowable bearing capacity of soil foundation. KPT tests were conducted at 13 boreholes each measuring 4.00 m long along the crown of the slope. The results indicated the compacted layer and located the firm layer of soil foundation. The average allowable bearing capacities were 1.53 t/m2 at depth of 1.00-5.00 m and 17.06 t/m2 for 5.00-6.00 m depth respectively. Furthermore this paper presents an analysis of the stability of a slope with the shear strength parameters of the soil and the geological profile were defined based on the results of KPT. The results of factor of safety were below the stable value for analysis cases with groundwater table. Test results demonstrate the usefulness of the KPT method in geotechnical investigations to estimate soil profile and bearing capacity efficiently and economically. This approach is also less time consuming compared to other geotechnical site investigation methods.

This paper presents a study on the strength and corrosion resistance of mortars made with binary blends of ordinary Portland cement (OPC) and ground rice husk ash (RHA) or ground palm oil fuel ash (POA). The mortar mixtures were made with Portland cement Type I containing 0-40% RHA and POA. RHA and POA with 1-3% by weight retained on a sieve No.325 were used. The water to binder ratio was kept constant at 0.5 and the flow of mortar was maintained at 110±5% with the aid of superplasticizer (SP). Scanning electron microscopy (SEM) was used for analysis. The compressive strength chloride penetration and corrosion resistance of the mortar were determined. The results show that strength as well as the resistance of mortar to chloride and corrosion can be improved by blending with RHA and POA. Thus RHA and POA have a high potential to be used as a good pozzolanic material.