The aim of this research is to create the center of mass testing machine for vehicles with maximum mass 3000 kilograms. By the performance of this machine is able to determine the center of mass 3 axis by horizontal longitudinal and vertical. On the other hand the verities of mass from 50 to 100 kilograms and the several of weight distribution at horizontal and longitudinal are applied to the condition of testing for reasonable to the position of the center of mass. The result of research discovered to the performance of center of mass tester was activated following to test conditions. Furthermore the weight distribution at longitudinal was the highest effect to the horizontal center of mass. By the way the value of weight distribution at horizontal is more effects to the longitudinal center of mass. Moreover increasing of mass was impact to the vertical center of mass and it’s independent to the position of weight distribution.

Currently transport has played an important role in everyday life resulting in huge traffic jams caused by big city streets and pollution problems from global warming to global temperatures are rising. Since humans are creatures that prefer comfort in all areas which contrasts with the higher temperatures of the Earth. Currently the use of air conditioning a lot. To modify the temperature is reduced in the range 2 3 to 25 degrees Celsius makes people feel comfortable. However the use of air conditioning in the car cabin cooling efficiency can be increased to a higher level than it is by cooling the refrigerant. The aim of this research is to test and compare the performance of car air conditioning systems usually equipped with a heat exchanger. Using water from the condensation of evaporator as a medium for heat transfer. By installing the equipment at the outlet of the condenser. This causes the temperature of the refrigerant is low. The pipe lengths in the equipment from the calculation of 1 .2 meters and copper lines that increases the length of the tubes was calculated to compare with a length of 1.6 meters to test the speed of the compressor 1000 1500 2000 and. 2500 rpm and a wind speed of 20 35 and 50 kilometers per hour. The results of experiment found that the temperature refrigerant equipment decreased from an average of 1.6 degrees Celsius the pipe length of 1.2 meters and 1.6 meters of pipe temperature drops 1.8 degrees average temperature attended Eva sufficiently reduced operator. It increases energy efficiency ratio averaged 6.68% of the pipe length 1.2 m and 22.24% at a length of 1.6 meters as well as to increase the coefficient of performance of the air conditioning system. 6 .6 9 % of the pipe length of 1.2 meters and a length of 1.6 meters at 22.4% with the key factor in optimizing the cars air conditioning system. Making the refrigerant from the condenser the temperature drops to pull heat out of the cabin through evaporator higher.

The aim of this research is to create the center of mass testing machine for vehicles with maximum mass 3000 kilograms. By the performance of this machine is able to determine the center of mass 3 axis by horizontal longitudinal and vertical. On the other hand the verities of mass from 50 to 250 kilograms and the several of weight distribution at horizontal and longitudinal are applied to the condition of testing for reasonable to the position of the center of gravity for vehicle. The result of research discovered to the performance of center of mass tester was activated following to test conditions. Furthermore the position of the horizontal of center of gravity depends on the weight distribution at horizontal axis and an increasing of mass under non-uniform along the longitudinal and horizontal axis. In term of the position of the longitudinal of center of gravity the weight distribution at longitudinal axis and an increasing of mass rate are points. Otherwise the weight distribution at longitudinal axis and an increasing of mass are effect to the position of the vertical of center of gravity.

Here we present an experimental study of the single-effect adsorption cooling system using activated carbon-methanol working pair. The test unit was comprised of an adsorber a condenser and evaporator in vertical alignment. Heating and cooling of adsorber was mainly done by hot and cold water circulating through the water jacket. The evaporator and condenser was heated or cooled by flows of water through the internal coil. The adsorber was analyzed for its cooling rate when cooling was done by two approaches either cooling water and/or three thermosyphon heat pipes which both methods gave shortest cooling time. The investigated heat source and sink temperatures are; hot water temperature supplied to adsorber (70 80 90 oC) and cooling water temperature supplied to condenser (5 10 15 oC). An ultrasonic wave generator was attached to the bottom end of the evaporator to generate wave frequency varied by 8 10 and 14 kHz during evaporation phase. The ultrasonic wave can obviously reduce the evaporation time of methanol as well as to improve the system performance in terms of COP SCP and VCP. The system performance was considerably comparable to those from literatures. The highest COP and SCP obtained from this system was 0.718 and 248.90 W/kg respectively.