This study aimed to use Poka-Yoke techniques to help prevent errors and reduce loss in Front Side Fender Model assembly process. The researchers used four tools in the 7QC tools which were Check Sheet Cause-and-Effect Diagram and Graphs to search for causes and ways to solve problems and Cause and Effect Matrix and ECRS Techniques. The study revealed that the main cause of the problems was that the incorrect assembled side fenders were submitted to another department. This mistake had bad effects on time and workforce spent for correcting work including more expenses. The mistakes occurred because there was no tool for detecting errors in the work piece. Therefore the researchers use Poka-Yoke techniques in order to decrease errors by designing a control system for target detection while it was moving through the process. After collecting data the study showed that before the improvement during January to August 2019 the number of problems caused by the process were 0.093. However the number of problems after the improvement during September to December 2019 reduced to 0. It was obvious that this improvement reduced the loss from the front side fender assembly process up to 100.

The study of the efficiency of fuel consumption by adjusting the fuel injection pressure is basically one optimization method to maximize the engine combustion. In this current study the Honda wave 110 cc. engine has been used to test in particular the fuel injection by adjusting the pressure of injector. To control the pressure of injection was made by automatic valve injectors with three different pneumatic pressure which were 2 2.5 and 3 bars respectively and the similar running distance of 5km. The results showed that at 2 bars the obtained fuel saving was 1020.68 km/L and the speed at 25.23 km/h which corresponded to the highest CO2 emissions during the engine combustion.

The purpose of this research is to study on variables affecting fuel injection performance of biodiesel fuel injection and pyrolysis fuel. To test for variables affecting the fuel injection performance of biodiesel fuel injectors and pyrolysis fuel. By experimenting and modeling using computer programs to compare results. Finally for to use the information in the design of the car nozzle to work well with Biodiesel and pyrolysis fuel. The tested fuels which are pyrolysis fuel Bio-diesel fuel and diesel fuel are tested by tester Anton Paar@ Stabinger Viscosmeter (model SVM 3000/G2) ASTM D341 standard. The result shown that the density of the fuel is increasing normally. However the viscosity of the diesel and biodiesel are strong increased whereas the reducing of temperature is unaffected to the pyrolysis fuel. The fuel injection performance test showed that the density and viscosity of fuel were the major variables that affected the injection performance of the fuel. In case of using pyrolysis oil Injection performance is trend to higher other fuels and cold conditions.

Recently the Thai industry has continually grown up and also plays a role to economic growth in the country which affects the many of automotive components to be in the market. While the degeneration and waste of automotive components had increased as well. Therefore a car hood is one of the automotive parts which damage from the accident. Consequently the researchers have created a prototype material to develop into the car hood which made from the husk and water hyacinth. The random mixture of water hyacinth and husk was attempted to more than 3 ingredients. By forming a flat plate with thickness between 1 to 3 millimeters was used as prototype of the car hood material in this research. Thus the mechanical properties such as compressing and bending test were attempted to by the universal testing machine. The results showed that using resin as a binder material (Reinforced resin by water hyacinth and husk) will have the less ability of energy absorption. While using polymers as a binder (Polymer resin by water hyacinth and husk) will have the better ability of energy absorption. The properly mixture between water hyacinth and husk referred to the energy absorbing properties is 50:50 because the least linear stiffness is 1.087 N/mm. Besides the ability of energy absorption is 1612444 J/m3 which is property of this ingredient can reduce the severity of the impact in the event of pedestrians collision in the best.

Nowadays an automotive industry steadily has been growing and playing a major role on economy development for many years. The crash box is one of the most important parts for safety but it was found that the crash boxes manufactured domestically are not met international standard requirements. This is due to process and material limitation. This process for automotive safety test requires high budget and there is unclear approach for specific test. Therefore a study of crash boxes referred to energy absorption project was conducted as an alternative choice of testing. Regarding to the problems as addressed above this project was aimed to design and test crash boxes which come in various structures; simple type corrugated type and honeycomb type of crash box. In addition it was also emphasized in studying energy absorption behavior and physical deformation of crash boxes after dynamic and static energy being applied. Numeric simulation and static test methodology of front collision were applied for these tests in reference to USA NCAP standard for automobile collision test. Testing all types of crash boxes indicated that the corrugated type was able to absorb energy at 2.8% and 5.9% higher than honeycomb type and rectangular type respectively. This is capable to pickup stress and strain continually and effecting to more energy absorb than another type. Additionally this corrugated structure is feasible and suitable for crash box design in automotive manufacturing.