Currently car theft in Thailand is one problem that affects the economy and involves transnational criminals although there are many anti-theft devices available on the market. These mechanisms include gear locking devices steering wheel locking devices clutch/brake locking systems TDS systems voice transmissions wireless door-lock remote control system and GPS car tracking devices. Of the mentioned devices the GPS tracking devices are interesting as they use the principle of connecting to the cell phone system to send on-demand the GPS location of the car to the owners phone in the case that the vehicle is stolen. However these devices are not popular in the marketplace because the service fees are quite expensive. Also the function of these devices is to send the vehicles location to the verified car owner so the protection function is activated after the vehicle is stolen and the owner is only then aware that the car has been stolen. This is different from the devices that researchers have developed. The researchers equipment for when someone tries to steal a vehicle is the system will detect the movement inside the car and send the GPS location to the car owner instantaneously. Additionally the device was developed by using LoRa technology to transmit the data giving a lower operating cost than by using a GPS tracking device as sold on the market presently.

The study of the efficiency of fuel consumption by adjusting the fuel injection pressure is basically one optimization method to maximize the engine combustion. In this current study the Honda wave 110 cc. engine has been used to test in particular the fuel injection by adjusting the pressure of injector. To control the pressure of injection was made by automatic valve injectors with three different pneumatic pressure which were 2 2.5 and 3 bars respectively and the similar running distance of 5km. The results showed that at 2 bars the obtained fuel saving was 1020.68 km/L and the speed at 25.23 km/h which corresponded to the highest CO2 emissions during the engine combustion.

The purpose of this research is to design and develop dummy (anthropometric test dummy) for motorcycle frontal collision test. The conceptual design of dummy is male aging between 25-55 years old 6 pieces of rib and deformable 76.2 mm. In order to performance test it was classified into 2 testing by static testing and dynamic testing. For static testing the energy absorption behavior between force and deflection or “ static curves” is determined. While dynamic testing is considered to the energy absorption behavior between forces and several velocities or dynamic forcedeformation curves impact acceleration impact force on sternum and injury severity with the relationship of viscous in velocity function. The results of the energy absorption behavior on chest of dummy from static testing the tendency of chest deflection is relatively low during the initial force and suddenly increasing when rise to the critical point. This behavior is similar to the energy absorption of the human chest. Therefore the design features of this test dummy can reflect behavior that is close to the human anatomy. In case of dynamic testing it is discovered the ability of the dummy testing to absorb up to 560 J impact acceleration 3 8 . 4 3 g impact force on sternum 5 . 0 9 4 kN. The viscous in velocity function is 0 . 8 2 5 m/ s which compared to injury severity at AIS3+ ( or higher than serious injury) . Therefore the dummy design in this research project corresponds to the collision test of a motorcycle.

A design and development of powertrain module crash test using with the motorcycle crash test is aim to create a special tool for automotive assessment and safety engineering based on the realistic test. In order to main system of power module tester is consisting of powertrain system using electrical motor transferring system using chains and gears and control direction system using dual rails respectively. Based on powertrain module tester performance crashing speed relative angle between target and distance before crash are regarded. Nevertheless the result of testing performance was conducted to statistic hypothesis test by Mean Absolute Deviation: MAD Standard Deviation: SD Mean Square Error: MSE Mean Absolute Percent Error: MAPE and Root Mean Square Error: RMSE. The results of this approach discovered that the crashing speed was the highest error with 96% and the lowest was distance before crash. Furthermore it was corresponding to the statistic hypothesis test. However the result of the error was influence of the rails distance which limit by funding. In case of crash energy the mean of energy was appeared on 10.978 J. Whereas the tendency of variable was similar to polynomial equation.

The purpose of this research is to study on variables affecting fuel injection performance of biodiesel fuel injection and pyrolysis fuel. To test for variables affecting the fuel injection performance of biodiesel fuel injectors and pyrolysis fuel. By experimenting and modeling using computer programs to compare results. Finally for to use the information in the design of the car nozzle to work well with Biodiesel and pyrolysis fuel. The tested fuels which are pyrolysis fuel Bio-diesel fuel and diesel fuel are tested by tester Anton Paar@ Stabinger Viscosmeter (model SVM 3000/G2) ASTM D341 standard. The result shown that the density of the fuel is increasing normally. However the viscosity of the diesel and biodiesel are strong increased whereas the reducing of temperature is unaffected to the pyrolysis fuel. The fuel injection performance test showed that the density and viscosity of fuel were the major variables that affected the injection performance of the fuel. In case of using pyrolysis oil Injection performance is trend to higher other fuels and cold conditions.