This research project presents about wind turbine simulation for connected single phase grid system using hysteresis current control technique to generate PWM signals for controlling a single-phase voltage source inverter. The simulation system presented here uses the program. MATLAB/Simulink in the simulation of the wind turbine connected to the shaft of a three-phase permanent magnet generator is produced by alternating current through the full bridge rectifier circuit. Then the power supply is applied to the single-phase inverter circuit which is connected to the single-phase autotransformer to power transfer to the single-phase grid system. The simulation results confirm the validity of the proposed system with satisfaction under various conditions.

This project is intended as a teaching medium air conditioning system and simulation of air conditioning system problems. Some of them have been modified to suit their teaching needs. Arduino microcontrollers are used to control the system. By starting the study of the air conditioning system thoroughly. The microcontroller is written to control the operation of devices like the air conditioning system when the system malfunction. It will be used to analyze the problems of air conditioning. The experimental set will display the voltage and current. The connection points of the air conditioning problem analysis. When the symptoms are bad. The analyst can solve the problem by connecting or pressing the button of the device. The results of the project. The test will measure the difference of the air conditioning unit. And read the amount of current and volume in the system. To diagnose abnormalities and choose a solution to the problem from the kit system that can be displayed to solve the problem that the analyst was correct or not with the LED status light. Based on the performance test a demonstration kit for the demonstration of efficiency of the air conditioning system was provided to 10 experienced air conditioning technicians. 80s of issues. The reliability of the demonstration set and the efficiency of the simulator case study of the electrical system in air conditioning systems is acceptable

Case Study Development of Welding Machine for Sterling Silver Jewelry Parts With 500-amp electrical arc system for welding closing porous jewelry after casting. The problem can be solved by welding closing porous or by the jewelry. It is an alternative to repairing the work piece. The efficiency of electrical arc welding equipment can be repaired to a certain extent. Based on the results of the experiments the welding and repairing porous porcelain parts were rated at 500 amperes by random sampling of 4 time slots 5 seconds 10 seconds 15 seconds and 20 seconds. Examine the most appropriate porous or porous workpiece for 20 seconds with 18 complete workpieces capable of sealing or milling. A good percentage of 90 percent of the performance of an electrical arc welding machine for welding sealing or cutting.

To Improvement the power factor is very important. Because the costs are increased or reduced. To Improvement the power factor the higher the value it is necessary to buildings offices and industrial buildings or the fact that the industry needs real power. And reactive power source to operate. This research presents the design and construction of reactive power factor control. Which amounted to 6 working order by the first sequence is divided into three three-phase electrical power system and three consecutive singles phase by active power different. first1 is reactive at 5 kVAr second 2 and third 3 are reactive at 2.5 kVAr forth 4 fifth 5 and sixth 6 precious marine active 0.83 kVAr control. the power factor controller that controls RG3-12 pay Oval active in various sequences. As a result when not equipped with reactive power compensation software to control the power factor. This makes the flow of the high and low Power Factor schedule. When equipped compensate reactive power source to power factor control. Single-phase motor 1 kW and light bulb 1640-watt making the current decline of 14 amps rest 12 amps of the power factor increases from 0.5 to 0.929. When connected to three-phase motor with 2 kW 0.8 2.2 flow down from 2.360 rests 0.942 amps of power factor value up from 0.308 to 1.0.

This research study investigated the structure and electrical effect of the La3+ and Sm3+ co-modified BaTiO3 ceramics with formula Ba1-(x-y)(LaxSmyTi)O3. The concentration of of x was fixed at 0.010 while that of y varied from 0.010 to 0.040. The ceramics are prepared by a solid-state mixed-oxide technique. The phase formation behavior is studied using x-ray diffraction (XRD) The dielectric properties with temperature are broad as wide temperature rang. Results showed that co-modified BaTiO3 ceramic ratio of 0.010 to 0.020 still tetragonal structure where the A-site is disturbed by a group of rare-earth doped. In addition we also found that the dielectric constant increases with ratio of 0.010 to 0.020 and respond to higher frequencies that can be used in the applications circuit with high frequency.