The objective of this research is to develop the precast adobe wall panel with high corrosion resistance and good thermal insulation. The ratio of Portland cement type1 clay rice husk ash straw rice husk waterproofed liquid and tap water was mixed and casted as same as the common concrete and reinforced by bamboo. From the results the proper prototype ratio of precast adobe wall panel was Portland cement type1: clay: rice husk ash: straw: rice husk: waterproofed liquid: tap water which equal to 1: 3: 0.3: 0.02: 0.02: 0.02: 0.4 by weight. The properties of the precast adobe wall panel prototype included density 1797 kg/m3 water absorption 16.70% bending strength 2.61 MPa compressive strength 21.40 MPa thermal conductivity coefficient 0.314 watt/m.Kelvin. Moreover the precast adobe wall panel prototype also was verified by TIS.2226-2548 with properties of impact resistance deflection and hardness in medium duty (MD) level. These straw and rice husk effected the precast adobe wall panel to decrease the density bending strength thermal conductivity coefficient and increase the compressive strength and water absorption.

Molds manufacturing to produce chloroprene rubber product with carbon steel over time the mold surface will wear. From the original. The practice in the industry often uses surface coatings (Hard chrome method) or change materials to create molds. Therefore this research is to study the effect of corrosion or wear. To see the size of surface mold changed in the experiment. Based on a tolerance of 0.1 millimeters at the molding point and after molding in the actual work conditions of a 2-3 weeks sample and mold size measurement. At less than 10 times the permissible coordinate value is 0.01 millimeters. The experiment found that. The wear of carbon steel molds was formed with chloroprene rubber. It has a very small value when referenced to the tolerance coordinates which is not significantly reduced when the rubber specimen size is determined. The allowance range is 10 μm to 100 μm. Therefore the design of chloroprene rubber to make molds with carbon steel. It can help reduce production costs. Without replacing with corrosion-resistant materials or adding coatings.

To Improvement the power factor is very important. Because the costs are increased or reduced. To Improvement the power factor the higher the value it is necessary to buildings offices and industrial buildings or the fact that the industry needs real power. And reactive power source to operate. This research presents the design and construction of reactive power factor control. Which amounted to 6 working order by the first sequence is divided into three three-phase electrical power system and three consecutive singles phase by active power different. first1 is reactive at 5 kVAr second 2 and third 3 are reactive at 2.5 kVAr forth 4 fifth 5 and sixth 6 precious marine active 0.83 kVAr control. the power factor controller that controls RG3-12 pay Oval active in various sequences. As a result when not equipped with reactive power compensation software to control the power factor. This makes the flow of the high and low Power Factor schedule. When equipped compensate reactive power source to power factor control. Single-phase motor 1 kW and light bulb 1640-watt making the current decline of 14 amps rest 12 amps of the power factor increases from 0.5 to 0.929. When connected to three-phase motor with 2 kW 0.8 2.2 flow down from 2.360 rests 0.942 amps of power factor value up from 0.308 to 1.0.

This research is a study of the optimum heat temperature for baking sintered castings for burnout removal of EC 500 type ash wax from cast mortar. Improving jewelry casting process to reduce waste from silver jewelry production process. By studying the temperature of the mortar. To burn remove wax from the mortar and clean the gaps. Then try to bring silver water instead of metal casting. The results of a baked casing study using the EC500 housing prototype from the study showed that the EC500 wax material is melted from all solids to ash wax by heating at 850 ° C to burn. Remove ash wax which makes the cavity clean. When the casting was casted with 925 sterling silver the most complete workpiece after the improvement of the waste jewelry casting process was found to be 1 piece 1 percent 99 pieces or 99 percent.

The purpose of this research is to study assessment of safety in construction of building projects. The safety assessment form was developed by referring to the Ministerial Regulations. The safety assessment composed of 8 categories: (1) construction site perimeter (2) electricity and fire protection (3) crane (4) passenger lift and material hoist (5) welding (6) fall protection (7) temporary scaffolding and stairs and (8) personal protective equipment. Based on the safety assessment of the construction site the size of the large building exceeds 2000 m2 and height exceeds 23.00 m. in the Bangkok metropolitan has of 20 buildings. The average of safety is 80 percent. By construction site perimeter the highest average and the fall protection has the lowest mean. So all parties involved workers contractors and project owner in particular need to focus on safety work to prevention against falls from high in order to reduce the loss of property life company reputation including the morale of the work as well.