This project is intended as a teaching medium air conditioning system and simulation of air conditioning system problems. Some of them have been modified to suit their teaching needs. Arduino microcontrollers are used to control the system. By starting the study of the air conditioning system thoroughly. The microcontroller is written to control the operation of devices like the air conditioning system when the system malfunction. It will be used to analyze the problems of air conditioning. The experimental set will display the voltage and current. The connection points of the air conditioning problem analysis. When the symptoms are bad. The analyst can solve the problem by connecting or pressing the button of the device. The results of the project. The test will measure the difference of the air conditioning unit. And read the amount of current and volume in the system. To diagnose abnormalities and choose a solution to the problem from the kit system that can be displayed to solve the problem that the analyst was correct or not with the LED status light. Based on the performance test a demonstration kit for the demonstration of efficiency of the air conditioning system was provided to 10 experienced air conditioning technicians. 80s of issues. The reliability of the demonstration set and the efficiency of the simulator case study of the electrical system in air conditioning systems is acceptable

The aim of this research is to design a prototype of a male dummy chest for motorcycle crash tests. The primary criteria discussed in this study are based on the unique features of Thai ergonomic body sizes with an age range of the highest fatal rate and the fundamental design of the Hybrid III 50th percentile male crash test dummy. A comprehensive experimental study of crash behavior of the prototype undergoing axial compressive loading is performed using the mutual procedure of cadaveric chest testing. For design criteria the largest chest deflection of 80 mm the maximum acceleration of 38.47g and the absorbed energy of 178.369 Joules are considered in the experiment. The obtained results show a good agreement with the experimental data of other researches in which the capability of the energy absorption depends on impact velocities. In addition the energy absorption capability of this prototype can accurately assess an injury level under AIS 3+. For this reason the first prototype of a male chest dummy is particularly suitable for an assessment of a lower serious injury level in a motorcycle crash test.

This research aimed to study powe generation from heat loss strove by thermoelectric generator unit. As cooking with a gas stove can cause heat loss between the stove and the cookware this heat loss from gas stove can be converted into the electricity. For the experiment the researcher used a gas stove model KB5 installed with thermoelectric plate model TEG1-241-1.4-1.2 connected in a series to the power of 4 modules. Then experimental conditions of the gas pressure in the gas strove were set at 0.1 0.2 0.3 0.4 0.5 and 0.6 kg/cm2 respectively while the amount of mixed air was constant during the experiment. The results showed that when the gas pressure was at 0.6 kg2 the temperatures of the hot side and cold side of the thermoelectric generator was equal 250.5oC and 65.5oC respectively. Lt also generated the highest electric power of 53.3 watts. The power conversion efficiency was 5.3% at 38.1 Volts with 1.4 Amperes. In addition when electric was connected to a thermoelectric generator unit with 12 VDC 7-watt LED bulb the gas pressure in the gas stove were set at 0.3 0.4 0.5 and 0.6 kg/cm2 respectively was affected by the difference between the heating temperature and the cold temperature in the range of 185o C that could lighten up LED bulb.

Nowadays the measurement technologies are continually growth in advanced. These can be seen in the developed and developing countries that research and develop the products which support the consumer behavior and/or country economy ic growth. However some advanced products are very expensive such as pH meter. Therefore this thesis develops the pH meter which allows the acid-base test of the water and it can be supported the agriculture. The proposed pH meter is included the pH pen sensor temperature sensor water level sensor. The proposed meter can measure the acid-base of the water by sending SMS alert signal via GSM module to the mobile phone of the farmer. As can be seen this thesis can prevent and solve the effect of the high acid-base of the water that possibly flows into the agriculture farm via using SMS alert signal of the mobile phone of the farmer.

This research was the application of Unmanned Arial Vehicle (drones) in conjunction with remote sensing technology to monitor the occurrence of the waste dump site fire. The research began with designing and developing prototype tools to collect data from the field site. After the tools were tested they were used to measure gases from the dumping sites. After that the field observation was performed in Nonthaburi Province Pathum Thani Province and Pha Nakhon Si Ayuthaya Province. The final step of the research was to collect the data of active fire hot spot and image from MODIS system satellite covered the area of Nonthaburi Province Pathum Thani Province Pha Nakhon Si Ayuthaya Province and Samut Prakan Province in the period of 1 November 2017 to 31 October 2018. The result showed that the developed drone and the prototype gas detection units worked as designed. The result of gases measurement by the tools were similar to the references equipment. The field observation showed that the dumping site mainly composted of plastic organic matter and cotton which up to 74.9 percent in total. This indicated the factor that influenced the dump site gas generation. Based on the combination technique in the research it could be concluded that Drone and Remote sensing technology were the compromised technology for monitoring fire from the municipal solid waste dump site area.